RESULTS AND CONCLUSIONS 1- Plot the graph between N, T, and n against Pi (on the same graph sheet). Electrical Engineering Dep. Electrical Machine Lab. 2- Plot the graph between N against T. 3- Comment on the curves obtained in view of the theoretical performance. 4- Why does the speed fall slightly when the DC compound motor is loaded.

RESULTS AND CONCLUSIONS 1- Plot the graph between N, T, and n against Pi (on the same graph sheet). Electrical Engineering Dep. Electrical Machine Lab. 2- Plot the graph between N against T. 3- Comment on the curves obtained in view of the theoretical performance. 4- Why does the speed fall slightly when the DC compound motor is loaded.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

405 / 5000 Find the slip, the powers converted,air gap, output and efficiency of a motorthree-phase induction in Y of 138.56 V of voltage ofphase, 60 Hz and 50 hp, which is supplied with 35 A at apower factor of 0.85 lagging. The losses are: copper stator, 2.5 kW rotor, 750 W friction and friction, 650 W and from the core, 1850 W, Negligible miscellaneous losses.
The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. The resistance of the armature circuit is 0.3 ohm. When the motor current is 30 A, speed is 900 r.p.m. If the current reduces to 20 A at lower speed, what arrangement should be made? Neglect any effect not included in the data given.
The reduced parameters of a 3-phase asynchronous motor with star connected stator, 50 Hz and 1450 rpm are given below.Rs=2.3 ohms, Rr'= 3ohms. Xsσ (X1)=4 ohms , X'rσ (X2) = 9 ohms, RFe= 450 ohms , Xm= 15 ohms.While 400 volts between phases is applied to the motor input, the motor consumes 3500 watts at its nominal speed. Calculate the efficiency of the machine using the L-equivalent circuit for this study?
EE 422 - AC and DC Machinery Solve the following problems completely. Box and Round-off your final answer in nearesttwo decimal places 1.A 25 hp,250V long shunt compound motor takes 5 A when running light and runs at 1150 rpm. Armature resistance, 0.15 ohm, Shunt field resistance, 200 ohm and series field resistance, 0.05 ohm. At rated load the motor takes 86.5A and runs at 720 rpm. Determine the ratio of torque developed from no-load to full load. answer: 1:34 2.A compound motor develops a torque of 271 lb-ft when it is operating at 1200 rpm, under which condition its armature current Ia is 215 amperes. What will be the developed horsepower of the motor if the load is increased so that it slows down to 1,1120 rpm in which case Ia changes to 238 amperes and the total flux increases by 8 percent? answer: 69.1hp
The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. Theresistance of the armature circuit is 0.3 ohm. When the motor current is 30 A, speedis 900 r.p.m. If the current reduces to 20 A at lower speed, what arrangement shouldbe made? Neglect any effect not included in the data given. (Ans.3.833 ohms)
Your assumption is that you measure Insulation Resistance [IR] using MeggerTest on an Induction Motor that works on a line voltage of 440 Volts 50 Hz with a measurable test result of 0.5 M Ohm. Question : a. What about your conclusion, is the measurement value still in accordance with the provisions of the Class Recommendation?. b. What are your actions to be able to maintain and maintain the best IR value of electric motors ?
4.a. When a d-c motor is tested by the electrical input method, the field rheostat is adjusted to giveA. rated speed at full load.B. rated speed at no load.C. maximum speed at minimum load.D. minimum speed at maximum load.4.b. When a machine is tested, the volume of cooling air is 1250 cfm. If the temperature of the entering air is 25 C and the temperature of the outgoing air is 35 C, the loss in the machine isA. 7.1 kw.B. 24.8 kw.C. 12.5 kw.D. 17.7 kw.
A 13 kW, 198 V DC short-shunt motor, being fed through a feeder with total resistance of 0.04 ohms, has an armature, series field and shunt field resistances of 0.01 ohm, 0.02 ohm and 44 ohms, respectively. Find the armature voltage. 2 decimal places only Please hand written solution
29) A 415 V Shunt motor takes a total current of 80 A . if the shunt field resistance is 40 ohms, the armature resistance is 0.25 ohms, and iron, friction, and windage losses amount to 1.5 kW, Determine I) Armature copper loss II) Field copper loss III) Total loss IV) Output power V) overall efficiency of the motor.
single-phase induction motor employed for a mechanical work at a rate of 45 HP. Its electrical power will be 33.57 kW. A)Estimate the amount of line current necessary to power the motor if the line voltage is 460 Volts assuming 100% efficiency and a power factor of 1. ( B)Now, estimate the necessary line current for this motor if its power factor drops to 0.65. Assume the efficiency and mechanical power as the same. C)What do these calculations indicate about the importance of maintaining a high-power factor value in an AC circuit?
The field and armature resistance of a 400V shunt motor are 200 ohms and 0.1ohm, respectively. The motor takes 30A of current while running at 1000 rpm. If the frictional losses are 400W, determine the motor efficiency.
A short shunt compound generator supplies a current of 100A at 220V. If the resistance of the shunt field is 50Ω, of the armature 0.05Ω, the total brush drop is 2V and the iron and friction losses amount to 1 kW, find the bhp of the engine driving this generator.