A separately excited DC motor with supply voltage of 420 V, armature resistance of 0.5 N and K_ =1.8 V-s/rad is controlled by regenerative braking using a DC chopper. Assuming constant average armature current of 320 A during regenerative braking, determine the speed of motor for a duty cycle of 0.65. m 1225 гpm 1629 гpm 1463 гpm 69 гpm

A separately excited DC motor with supply voltage of 420 V, armature resistance of 0.5 N and K_ =1.8 V-s/rad is controlled by regenerative braking using a DC chopper. Assuming constant average armature current of 320 A during regenerative braking, determine the speed of motor for a duty cycle of 0.65. m 1225 гpm 1629 гpm 1463 гpm 69 гpm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. A dc shunt motor operating unloaded at a terminal voltage of 125V at a speed of 1420 rpm. When themotor is operated unloaded at the same terminal voltage but with an additional resistance of 8Ω in serieswith the shunt field, the motor speed is 1560rpm. (Ignore armature reaction and magnetic saturation)a) Calculate the resistance of the shunt field.b) Calculate the motor speed if the series resistance is increased from 8Ω to20Ω. c) With the field resistance at its original value and no series resistance, calculate the motor speed if it isoperated loaded at a terminal voltage of 90 V and a terminal current of 100A.
A 240V shunt motor, running on no-load and at normal speed, takes an armature current of 2.4 A froma 240Vsupply. The resistance of the field circuit is 240Ω, and that of the armature is 0.25Ω. Calculatethe motor output power and efficiency when drawing a line current of 35 A from the supply
the step-by-step solution needed with calculation. 45) A 40hp, 440V, 4 pole dc motor has an armature wave-wound with 846 conductors and the commutator has 141 segments. The full load efficiency is 85% and the shunt current is 1.25A. If the brushes are shifted backward through segments from the geometric neutral axis, calculate (a) The demagnetizing ampere-turns per pole (b) The distorting ampere-turns per pole on full load. the previous one is wrong.
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. calculate emf at full load of dc motor
Give answer as soon as possible A 200 V dc shunt motor runs at no-load speed of 1000 rpm and takes line current of2 A. When it runs at rated load, the speed of the motor reduces to 920 rpm. Ifsupply voltage is constant, then calculate the line current drawn by the motor atrated load and mechanical power developed by the motor (neglect magnetic andstray load losses).
a shunt-wound motor runs at 600 r.p.m from a 230 V supply when taking a line current of 50 A. its armature and Field resistance are 0.4 ohms and 104.5 ohms respectively. Neglecting the effects of armature reaction and allowing 2 V brush drop, calculate (a) the no-load speed if the no-load line current is 5 A. (b) the resistance to be placed in armature circuit in order to reduce the speed to 500 r.p.m when motor is taking a line current of 50 A . (c) the percentage reduction in the flux per pole in order that the speed maybe 750 r.p.m when the armature is 30 A with no added resistance in the armature circuit.
A 220 V dc shunt motor takes 5A and 40A at no load and full load respectively. It has an armatureresistance of 0.2 ohm and field resistance of 110 ohm respectively. Iron, Friction and Windages lossesare negligible. Then using among parameters find following: 1. Calculate an emf at no load of dc motor 2.Determine the armature current at full load 3. Determine armature current at no load 4.Calculate an emf at full load
Q/ dc shunt motor 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * Cu loss is……watt * Mechanical , electrical and overall efficiency …… Output of the prime motor…….kwatt * The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * Flux per pole is......... wb * E.M.F. generated is………….volt *
1- A 10kW, 200V, DC Shunt motor has 1-ohm armature resistance. At the starting of the motor, its back emf (Eb) is zero.Select one:TrueFalse 2- Identify which of the following loss is not varying with respect to load current? a.Iron loss b.Both Armature and Series field copper losses c.Series field Copper Loss d.Armature Copper Loss
A 220V,100A dc series motor has armature and field resistances of 0.04 and 0.06 ohm respectively.Running on test, on no load has a seperately excited generator at 1000 rpm gave the following result Field Current(A)- 25 50 75 100 125 150 175 Terminal Voltage(V)- 66.5 124 158.5 181 198.5 211 221.5 Machine is connected for dynamic braking with braking resistance of 1.5 ohm.Calculate motor current and torque for a speed of 800 rpm.
A 230V shunt motor has an armature resistance of 0.28Ω and a field resistance of 115Ω. At no-load, the line current is 8A and the speed is 2300rpm. What is the speed when the line current is 52A? Assume brush drops of 1V at no-load and 3V at load condition and constant flux density. 2154rpm 2212rpm 2178rpm 2155rpm
A 118 V, 50 Hz, single-phase synchronous motor is taking a current of 40 A at 0.85 lagging power factor. The effective armature resistance is 0.47 ohm. Iron and friction losses amount to 158 W. Determine the percent efficiency of the motor at this load. Neglect losses in the excitation.