4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the bars are balanced to share the load equally. Dismissing any chance of buckling, determine the final stresses when an additional load of 20 KN is added. Use Esteet = 205 Gpa, Ecopper = 100 Gpa. Steel 20KN Copper Steel 2.5m 3.6m

4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the bars are balanced to share the load equally. Dismissing any chance of buckling, determine the final stresses when an additional load of 20 KN is added. Use Esteet = 205 Gpa, Ecopper = 100 Gpa. Steel 20KN Copper Steel 2.5m 3.6m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm2 cross-sectional area and rod EF has a 600 mm2 cross-sectional area.State whether the structure is statically determinate or indeterminate. Why?Determine the force and the stress in each rod.Determine the deformation of each rod. Note: The link BED is rigid, and BE = ED.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q = 2 kips, R = 16 kips and S = 20 kips.
The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 2850 mm2 and an allowable normal stress of 105 MPa. Bar (2) has a cross-sectional area of A2 = 3950 mm2 and an allowable normal stress of 160 MPa. Assume x1 = 1.9 m, x2 = 2.7 m, y1 = 1.5 m, and y2 = 2.6 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A timber column, 8 in. by 8 in. in cross section, is reinforced on all four sides by steel plates, each plate being 8 in. wide and t in. thick. Determine the smallest value of tfor which the column can support an axial load of 300 kips if the working stresses are 1200 psi for timber and 20 ksi for steel. The moduli of elasticity are 1.5 x106psi for timber and 29 x 106psi for steel.
A timber column, 8in. by 8in. in cross section is reinforced on all four sides by steel plates, each plate being 8in. wide and "t"in. thick. Determine the smallest value of "t" for which the column can support an axial load of 300 kips if the working stresses are 1200psi for timber and 20ksi for steel. The moduli of elasticity are 1.5x10^6psi for timber and 29x10^6psi foe steel -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.Answer: Pmax = Enter your answer in accordance to the question statement kN
The rigid bar AB with a length of 5m, is attached to two vertical rods and ishorizontal before the uniformly varying load of zero intensity at point A and 10kN/mat point B is applied. The rod at A is steel with L=3m, A=300 mm2 and E=200GPa. Therod in B is aluminum with L=4m, A=500mm2 and E = 70GPa. Determine the verticaldisplacement of the bar at a point where the resultant of the load is acting.
Construct the buckling curve, P/A versus L/r, for a column that has a bilinear stress–strain curve in compression as shown.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips.Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.