Question 3 A column of 7 m effective length is to be made by welding two 228 x 12 mm plates to a W200 x 52 as shown. Determine the allowable centric load if a factor of safety of 2.3 is required. Use E = 200 GPa. For an W200 x 52 section, IÂ =(52.7×10°)mmª, I¸ = (17.8×10º)mmª . 114 mm 114 mm ·x

Question 3 A column of 7 m effective length is to be made by welding two 228 x 12 mm plates to a W200 x 52 as shown. Determine the allowable centric load if a factor of safety of 2.3 is required. Use E = 200 GPa. For an W200 x 52 section, IÂ =(52.7×10°)mmª, I¸ = (17.8×10º)mmª . 114 mm 114 mm ·x

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 60 mm dimension and as a fixed ended column about an axis perpendicular to the 30mm dimension. Determine the safe central load using a factor of safety of 2.5 and E = 70 Gpa.
Determine if the following column is long or short, and then determine the critical load on a steel column having a rectangular cross-section, 12mm by 18mm and length of 250 mm. it is fixed on both ends and made from a steel that has the following properties: E=209 Gpa and Sy=290 Mpa.
Question 3. Determine the crippling load for a I-section of dimensions 12 cm × 12 cm × 2 cm and of length 5 m when it is used as a strut with both of its ends fixed. Take E = 2 × 105 N/mm2.
A spreader bar is used in the assembly shown in the figure attached. It is made of a circular steel ros of diameter 32mm. Assuming that the cables and their connections are inextensible, determine largest load W that can be applied so that the spreader bar does not buckle. Both end of the spreader bar may be assumed to be pin connected. The youngs modulus of the spreader bar is, E = 200 x 10^3 N/mm^2.
Determine the critical load of a pin-ended steel tube that is 5 m long and has a 100-mm outer diameter and a 16-mm wall thickness. Use E=200 GPa.
A circular-cross-section bar with a diameter of 50mm and a length of 1.25 m is axially loaded. The baris made of medium-carbon steel. Both ends are pinned.Determine(a) Whether the Johnson or the Euler formula shouldbe used.(b) The critical load.
Member AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins at A and B pass through the centroid of the cross section of the channel, determine the factor of safety for the load shown with respect to buckling in the plane of the figure when θ= 30°. Use Euler’s formula with E= 200 GPa.
The horizontal link BC is 6.35 mm thick, has a width w = 31.8 mm, and is made of steel with ultimate tensile strength equal to 483 MPa. What should be the factor of safety to be used if the structure shown is designed to support a load P = 44.5 kN.
Assume that the wood column is pinned top and bottom for movement about the x-y axis, and ixed at the bottom and free at the top for movement about the y-y axis. Determine the maximum eccentric load P that canbe applied without causing the column to buckle or yield. Ew = 1.8(103) ksi, sY = 8 ksi.
As shown below, the hydraulic cylinder at C is used to pull a bar from a pump, which is connected to a support ABC at A. The critical elements are the diameter dr of the bar and the diameter dp of the pin at B. For a factor of safety FS = 3.0, determine the required diameters if the maximum load on the bar suction for Pa = 15 kN. The failure voltages of the bar and pin are σe = 340 MPa and τe = 400 MPa, respectively.
Determine the critical load of a round wooden dowel that is 48 in. long and has a diameter of (a) 0.375 in., (b) 0.5 in. Use E=1.6 *106 psi