roblem 2 The following two three-phase loads are connected to a three-phase system of 311.13 cos (377 t) V line: 1) Three-phase induction motor of 10000 VA in Y with a power factor of 0.6 2) Three-phase load balanced in Δ with Zf = 20 ∠ 323.13 ° Ω. Please find a) total current in each line, b) the apparent and reactive power and c) the copper losses that occur.

roblem 2 The following two three-phase loads are connected to a three-phase system of 311.13 cos (377 t) V line: 1) Three-phase induction motor of 10000 VA in Y with a power factor of 0.6 2) Three-phase load balanced in Δ with Zf = 20 ∠ 323.13 ° Ω. Please find a) total current in each line, b) the apparent and reactive power and c) the copper losses that occur.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.47P: Two three-phase generators supply a three-phase load through separate three-phase lines. The load...

See similar textbooks

Similar questions

For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real power (state whether it is delivered or absorbed). (c) the reactive power (state whether delivered or absorbed). (d) the power factor (state whether lagging or leading). [Note: By convention the power factor cos() is positive. If | | is greater than 90, then the reference direction for current may be reversed, resulting in a positive value of cos() ].
The resistance and reactance of the single-phase 60Hz transmission line conductors are 7.6 ohm and 6.6 ohm respectively. The transmission line delivers 20MW at a power factor of 0.66 lagging to the load with 54kV receiving end voltage. Determine the following a) The inductance of the transmission line in mH b) Sending end power factor c) Percentage voltage regulation d) Percentage Efficiency
5. Solve the following problem: A THREE-PHASE GENERATOR SUPPLIES THREE LOADS IN PARALLEL BY MEANS OF A TRANSMISSION LINE (CONDUCTORS) OF 0.4 + J0.5 OHMS. LOAD No1 5.0 KVA AND POWER FACTOR OF 0.85 BACK. LOAD No2 8.0 KW AND 3.0 KVAR. LOAD No3 6.0 KVA, POWER FACTOR OF 0.80 BACK AND 480 VOLTS. DETERMINE THE GENERATOR PARAMETERS (POWER, POWER FACTOR, OHMS, CURRENT AND VOLTAGE MAGNITUDE).
A 250V, 50 Hz single-phase supply feeds the following loads (i) incandescent lamps taking a current of 10A at unity power factor, (ii) fluorescent lamps taking 8A at a power factor of 0.7 lagging, (iii) a 3 kVA motor operating at full load and at a power factor of 0.8 lagging, and (iv) a static capacitor. Determine, for the lamps (incandescent and fluorescent) and motor, (a) the total current, (b) the overall power factor, and (c) the total power. (d) Find the value of the static capacitor to improve the overall power factor to 0.975 lagging.
Electric Machine; Check image, all question there. Consider the above approximate equivalent circuit for IM. A six-pole, 220Volt (line to line), 50Hz, Y connected, three phase IM has the following on a per phase basis: R1=0.5Ω , R2=0.25 Ω, X1=0.75 Ω, X2=0.5 Ω, Xm=100 Ω, Rc=500 Ω The friction and windage loss is 150 W. Determine the following at its rated slip of 3.5% a)Total Impedance(Zt) b)Rotor Copper Loss c)Core loss(Pm) d)Shaft Power(P0) e)Efficiency
A single phase AC distributor AB 500 m long is fed from end A and is loaded as under: (i) 70A at 0.707 p.f. leading150m from point A (ii) 30A at 0.8 p.f. lagging 500m from point A The load resistance and inductive reactance of the distributor is 0.3 Ω and 0.2 Ω per kilometer. If the voltage at the far end (B) is maintained at 230V, calculate the voltage at the sending end. The load power factor is referred to the voltage at the far end.
A short three phase transmission line has an impedance per wire of (15 + j20) OHMS. The sending end voltage is 13 kV and the receiving end takes 1 MW at a lagging power factor. The current per conductor is 70 amperes. Determine the efficiency of transmission, the receiving end voltage and power factor. Expected Answer: efficiency = 81.93%, receiving end voltage = 10.08 kV, power factor = 0.8179 lagging Please Provide Full Solution:
Non-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and blue phases respectively of 3-phase, 4 wire . The line voltage is 400. If a three phase motor is now started ,taking 150 A from the lines at a power factor of 0.3 lagging What should be the total current in each line and the neutral wire? Find the total real and reactive power supplied to the loads
A single phase transmission line is delivering 490 kVA load at 14 kV. Its resistance is 6 Ω and inductive reactance is 7 Ω if the load power factor is 0.7 lagging. Determine the: A) Current through the line. B) Sending end voltage. C) Sending end power factor. D) Regulation of transmission line. E) Efficiency of transmission line.
A single phase transmission line is delivering 470 kVA load at 14 kV. Its resistance is 4 Ω and inductive reactance is 8 Ω. If the load power factor is 0.9 lagging. Determine the 1Current through the line: 2Sending end voltage: 3Sending end power factor: 4Regulation of transmission line: 5Efficiency of transmission line:
A 3 phase synchronous generator has a synchronous reactance Xs of 9 Ω perphase, a no-load line to neutral AC voltage E of 12 kV and a line to line terminalvoltage of V of 17.3 kV.(a) Derive the formula for the 3 phase power produced by the generator in terms ofthe power angle δm, |V |, |E|, and Xs. (δm is the angle between E and V ).(b) The power angle δm = 30 degrees. Calculate the 3 phase real power delivered to thegrid at the terminals of the generator.(c) The real power increases when the power angle δm increases, but there is amaximum possible theoretical power that the generator can produce. Calculate themaximum 3 phase real power. Solve A-C
A 228/-30 volt constant potential generator delivers load to an impedance. Assumingthe reactance only to be variable and the line impedance is (6 + j4.5) ohms, calculatefor maximum power transfer: a) the load impedance, b) the current, and c) the loadpower and power factor.