Rod OA rotates counterclockwise at a constant angular rate -4 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r= (1.6 cos ) m. Both collars have a mass of 0.7 kg. Motion is in the vertical plane. (Figure 1) Figure 1 of 1 r=1.6 cos 0. 84 rad/s 0.8 m Part A Determine the magnitude of the force which the circular rod exerts on one of the collars at the instant Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) LOW HA 35.8 N Submit Previous Answers * Incorrect; Try Again; 4 attempts remaining Part B Determine the magnitude of the force that OA exerts on the other collar at the instant = 45. Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) FOA-ON Previous Answers

Rod OA rotates counterclockwise at a constant angular rate -4 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r= (1.6 cos ) m. Both collars have a mass of 0.7 kg. Motion is in the vertical plane. (Figure 1) Figure 1 of 1 r=1.6 cos 0. 84 rad/s 0.8 m Part A Determine the magnitude of the force which the circular rod exerts on one of the collars at the instant Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) LOW HA 35.8 N Submit Previous Answers * Incorrect; Try Again; 4 attempts remaining Part B Determine the magnitude of the force that OA exerts on the other collar at the instant = 45. Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) FOA-ON Previous Answers

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer correctly. Use Force-Mass-Acceleration Method. Don't just copy the others answers. Explain. A 0.25-kg hollow square thin plate is pin-connected to a wall with an outer side length of c = 15 cm and an inner side length of b = 13 cm. At the instant shown, the plate is subjected to a vertical force of P = 5 N (at the outermost corner), with a clockwise angular velocity of ω = 10.888 rad/s. Determine the (a) angular acceleration of the plate, and the (b) horizontal and vertical reactions at pin O.
show a derivation of the kinetic energy rotation about a fixed axis by proving an equation of T=1/2 Io w^2.
In the system shown in the figure, mA = 2 kg and mB = 5 kg.the mass is connected to each other by rope. A 12 N Fforce is applied to body A at an angle of 10 °.There is only friction between body B and the inclined planeand the kinetic coefficient of friction is 0.3. a) Draw the free body diagram of each object. b) Find the acceleration of the system. g = 9.8 m / s ^ 2, sin (37 °) = cos (53 °) = 0.60, cos (37 °) = sin (53 °) = 0.80, sin (10 °) = 0.17,cos (10 °) = 0.98
Dynamics Question If the normal acceleration of the rods is just w^2 * 1.5m, is the normal acceleration of the 50-kg bar just w^2* 2m?
Determine the acceleration of body B in Fig. P-1056, assuming the pulleys to be weightless and frictionless. Ans. aB = 5.85 ft per sec2
A small 0.18 kg metal ball is tied to a very light (essentially massless) string that is 0.60 m long. The string is attached to the ceiling so as to form a pendulum. The pendulum is set into motion by releasing it from rest at an angle of 50 degrees with the vertical. I solved that the speed of the ball when it reaches the bottom of the arc is 2.0 m/s and the tension of the string is 3.0 N What is the centripetal acceleration of the ball at this point?
simple pendulum is made of a 50 cm-string and a bob of mass m. At t= 0, the pendulum is at its equilibrium position and is given an initial velocity v = 0.2 m/s. The maximum angular speed, O'max, is:
The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
The figure below is a system consisting of two masses MA = 1.82 kg and MB = 3.6 kg, whose distance from the pore axis is R₁ = R₂ = 15 cm, while the angular positions are 0₁ = 30° and 0 = 150° . Determine the weight and position of the balancing mass placed on planes C and D if the distance from the axis RC = RD = 15 cm.
Determine the magnitude of W in Fig.P-1058 so that the 200-lb body will have an acceleration up the plane of 4.025 ft per sec2.Ans. W = 340 lb
A mass less spring having a spring content k=185 N/m, is inside a horizontal barrel. It's left end is rigidly fixed at position z= 0.0 cm, and it's right end is at X=L, where L=19.7 cm. The spring is then squeezed so that the right end of the spring is at the X=s, where S=13 cm. A ball of mass 50g is put in front of the spring and the spring is released. Calculate the speed of the ball in m/s. as it comes out of the barrel. Ignore friction Inside the barrel.
A 3.08-g bullet embeds itself in a 1.7-kg block, which is attached to a spring of force constant 827-N/m. If the maximum compression of the spring is 4.45-cm, find the time of the bullet-block system to come to rest. Provide your final answer in milli seconds.