SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in the diagram at an average velocity of 4.3 m/s. For . SAE 30W oil, p= 891 kg/m andp = 0.29 kg/(m-s). D =9 cm SAE 30W oil Hg 2.5 m Calculate the expected reading h of the mercury manometer in m. The density of oil and mercury is 891 kg/m and 13550 kg/m3 respectively. m. The expected reading h of the mercury manometer is

SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in the diagram at an average velocity of 4.3 m/s. For . SAE 30W oil, p= 891 kg/m andp = 0.29 kg/(m-s). D =9 cm SAE 30W oil Hg 2.5 m Calculate the expected reading h of the mercury manometer in m. The density of oil and mercury is 891 kg/m and 13550 kg/m3 respectively. m. The expected reading h of the mercury manometer is

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

A medical syringe (shown below) is used to inject a patient with a local anaesthetic before performing outpatient surgery. The anaesthetic can be modeled as an incompressible fluid with specific gravity, S = 1.02. Determine the plunger velocity, in units of in/s, if the anaesthetic is to be delivered at a constant 7 cm3 s −1 when the syringe is modeled as being perfectly sealed, and there is backward leakage between the plunger and syringe at a rate of 10% of the volume flow rate delivered through the needle. Note that anaesthetic is still to be delivered to the patient at 7 cm3 s −1 , despite this leakage.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
Consider coolant in a circular pipe to be in laminar flow; the following formula gives one-dimensional velocity: V=Vmax*(1-((r/R)^2)) Vmax = 2 m/s R = Radius of Pipe = 0.05 m Fluid Density (uniform) = 300 kg/m^3 1. What is the coolant flow (m^3/s)? 2. What is the coolant average velocity in the pipe (m/s)? 3. What is the true kinetic head of flow expression?
Using the data given in the schematic attached, find the difference of pressure PA and PB h1= 0.65m h2= 0.1m h3= 0.75m h4= 0.45m Density of fluid A is pA= 900kg/m3 Density of fluid B is pB= 1034kg/m3 Mercury density is pHg= 13600kg/m3 Oil density is poil= 700kg/m3 (In the given figure, the pipelines are parallel to each other and not necessarily at the same height.)
A pipe has a cross-sectional area of 16.5cm2 at point A, where the speed of the fluid (water) is 1.2 m/s and the pressure is 2.00 atm. The pipe ascends 3.00 m and narrows to 8.20 cm2 at point C. a) what's the speed of the fluid at point C. b) what's the absolute pressure at point C.
The pressure in a section of a horizontal pipe of diameter d1 = 2.0 cm is p1 = 142 kPa. The water flows through the pipe at a volumetric flow rate V = 2.8 L/s. If the pressure at a certain point is reduced to p2 = 42.6 kPa, due to a throttling of a pipe section, what should the diameter d2 of the throttling section be? Consider the density of water ρ = 1.0 g/cm3. Choose the correct option:
Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.81 cm and the other end is 0.28 cm. The larger and smaller ends are located 10 m and 4 m, respectively, from the datum line. If the flow at the 10 m datum line is 1.60 m/s and the pressure is 5244 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
In fluid flow equations, the variable p/ϒ is called A. Pressure Head B. Velocity HeadC. Static Head D. Total Head
Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for P1, P2 and p3, respectively, what are the head loss between 1-3 in meters.
Question : Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate, as shown in the figure. The force required to hold the plate steady is 75 N. Assuming steady, frictionless, one-dimensional flow, estimate Part (a) the velocities at sections (1) and (2) and Part (b) the mercury manometer reading h.