Section 5.1.4 Deforming Control Volume 5.30 (WILEY A hypodermic syringe (see Fig. P5.30) is used to apply a vaccine. If the plunger is moved forward at the steady rate of 20 mm/s and if vaccine leaks past the plunger at 0.1 of the volume flowrate out the needle opening, calculate the average velocity of the needle exit flow. The inside diameters of the syringe and the needle are 20 mm and 0.7 mm. Qleak Qout

Section 5.1.4 Deforming Control Volume 5.30 (WILEY A hypodermic syringe (see Fig. P5.30) is used to apply a vaccine. If the plunger is moved forward at the steady rate of 20 mm/s and if vaccine leaks past the plunger at 0.1 of the volume flowrate out the needle opening, calculate the average velocity of the needle exit flow. The inside diameters of the syringe and the needle are 20 mm and 0.7 mm. Qleak Qout

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

. Water flows at 6 gal/min through a small circular hole in the bottom of a large tank. Assuming the water in the tank approaches the hole radially, find the velocity in the tank at 2, 4 and 8 in from the hole.
A rectangular plate of weight 6 kg is suspended vertically by a hinge on the top horizontal edge .The cg of the plate is 10cm from the hinge. A horizontal jet of water 2cm diameter ,whose axis is 15 m below the hinge, impinges normally on the plate with a velocity of 5m/Sec . Find the horizontal force applied at the cg to maintain the plate in its vertical position. find the corresponding velocity of the jet if the plate is deflected through 30 degree and the same for continues to act at the cg of the plate
Water at a guage pressure of 4 kPa flows at a rate of 250 l/s in a 135° pipe bend of diameter 300 mm, find in MN the magnitude and direction of the resultant force on the bend.
A liquid enters a diffuser at speed 10.8 feet/second. The diffuser's inlet diameter is 4 inches while it's outlet diameter is 6 inches. Determine the speed of the water at the diffuser outlet in feet/second.
Suppose a u-bend is redirecting a flow of water. The water enters flowing to the right at 10 m/s. The u-bend completely reverses the direction of the flow, so the water leaves flowing to the left. The area of the u-bend is constant, a circular cross-section of 0.12 m. The pressure in the fluid is measured at 50 kPa. The length of the u-bend is 0.46 m. Find the force, including magnitude and direction, to hold the u-bend in place.
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
For a centrifugal pump of impeller diameter D rotating at N to develop a head of H and discharge Q, what would be the new head developed by a similar pump if we double the impeller diameter to 2D at constant impeller speed?
Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid against a head of 25 m. The diameter of the impellers being 24 cm and the speed of 1800 rpm. A pump is to be made up with a number of stages in series of similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a totalhead of 250 m. Find the diameter of the impellers and the number of stages required in this case. Answer: D = 46.63 cm, n = 6 stages
If the velocity of flow in a 75 mm diameter fire hose is 0.5 m/s,what is the velocity in a 25 mm diameter jet issuing from anozzle attached at the end of the pipe.
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
Suppose the pump of Fig. is situated between two large water tanks with their free surfaces open to the atmosphere. Explain qualitatively what would happen to the pump performance curve if a valve in the piping system were changed from 100 percent open to 50 percent open, all else being equal. Repeat for the system curve. What would happen to the operating point—would the volume flow rate at the operating point decrease, increase, or remain the same? Indicate the change on a qualitative plot of H versus V. , and discuss.