Shallow Foundation, Suppose that you are to design a foundation with a depth of 1.2m. It was also observed that the groundwater table is located 0.5m from the ground. Design a rectangular or a square footing that can carry a gross weight of 5kN. Use a factor of safety of 2.5

Shallow Foundation, Suppose that you are to design a foundation with a depth of 1.2m. It was also observed that the groundwater table is located 0.5m from the ground. Design a rectangular or a square footing that can carry a gross weight of 5kN. Use a factor of safety of 2.5

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 9.16P

See similar textbooks

Related questions

Q: Question attached

Q: A circular footing with a 1.52 m diameter is to be constructed 1.22 m below the ground surface.…

Q: 1. a) A continuous footing is 2.0 m wide and is founded at a depth of 1.5 m in a deep layer of sand…

Q: A circular footing with a diameter of 3m, if the allowable bearing capacity of the site is 220…

Q: A rectangular footing 8 m x 12 m carries a uniformly distributed load of kN/m?. Evaluate the…

Q: It is planned to construct a rectangular foundation with base dimensions of 8 * 14 m (B* L) on the…

Q: For a square foundation, according to the information given and the assumption of vertical load, it…

Q: 5. A column carrying a load of 750 kN is to be founded on a square footing at a depth of 2 m below…

A: From Terzaghi's analysis, the Terzaghi's bearing capacity factors are, for ϕ=18°:…

Q: Question attached

A: The maximum capacity of the pile depends on the superstructure load and the subgrade soil bearing…

Q: A strip foundation with dimensions B has to be constructed on sandy soil. The foundation will be…

A: Depending on the mechanism from which the deep foundation derives its bearing capacity, its shape…

Q: of safety is 3. Using Terzaghi's Bearing capacity equation, determine the design load on the…

A: Give data A=1.5m×1.5m Friction angle, ϕ=28o C=15.2kPa unit weight=19.8kN/m3

Q: using ONE – WAY ECCENTRICITY equation. g =105 lb/ft3, c = 0,  = 35, B = 5 ft, Df

A: The square footing is shown in the figure.

Q: Problem attached

A: Shear test - this test is done to determine the failure strength of the set. This test was also used…

Q: A square footing 2m x 2m, is to be constructed at a depth of 1.5m below the surface of a deep…

Q: Suppose that you are to design a foundation with a depth of 1m. It was also observed that the…

A: Solution: Given: Gross weight = 5 kN D = 1 m G.W = 0.4 m F.O.S = 2.5

Q: Question attached

A: Given:- D=1mcolumn load =1500kNc'=15kN/m2∅'=24γ=18.5kN/m3To find:-B

Q: A rectangular footing 2.0 m by 3.0 m is built in a homogeneous bed of sand of having bulk unit…

Q: A strip footing for a masonry wall is 1.1 m wide and is supported by the soil profile shown in the…

Q: The foundation design for the constmction of a telecommunication mast is to support a concentric…

Q: 3. A rectangular footing 5 ft x 2.5 ft is shown. Use the Meyerhof equation for the ultimate load for…

Q: Determine the allowable soil bearing capacity of a frictionless soil for a 6 ft wide square footing,…

Q: A column carrying a load of 750 kN is to be founded on a square footing at a depth of 2m below the…

A: Given data: Depth of footing (DF)=2 mCohesion (C)=30 KPasafe load =750 KN

Q: The ultimate load, Qu (assume two-way eccentricity) for a square foundation as shown in Figure, with…

Q: Refer to Figure 5.2 and consider a rectangular foundation. Given: B = 1.5 m, L = 2.5 m, Df = 1.2 m,…

A: Solution Given Data B = 1.5 m, L = 2.5 m, Df = 1.2 m, H = 0.9 m, Φ' = 40º, c' = 0, and γ = 17 kN/m3.…

Q: A square foundation is 1.5 m by 1.5 m in plan with other characteristics shown in the figure. The…

A: Given: The void ratio is 0.60. The specific gravity of soil is 2.65. The size of the square footing…

Q: A square foundation is 1.5 m X 1.5 m in plan. Given the soil properties supporting the foundation…

Q: A shallow continuous foundation is to be constructed on a soil under the ground' surface as shown in…

A: INTRODUCTION: Bearing capacity of soil: It is the strength or ability of soil to sustain the load…

Q: For the square footing shown, determine the gross allowable load per unit area (qai) that the…

Q: A continuous foundation is shown. If the load eccentricity is 0.2m, determine the ultimate load, Qu,…

A: e = 0.2m B = 2m Df =1.5m It has been asked in the question to determine the Ultimate load QU.…

Q: Explain the problem attached

A: since type of shallow footing is not provided we assumed it to be strip footing Nc=5.7,Nq=1,Nϒ=0,…

Q: SITUATION 27: A soil has a unit weight of 18.5 kN/m³ and a cohesion of 30 kPa. The angle of internal…

A: Given: Cohesion Angle of internal friction Depth of foundation Factor of safety To find: Allowable…

Q: The square footing shown below must be designed to carry a 294 kN load. Use Nc = 57.8 ; Nq = 41.4…

A: Given W=294 kNr=18.15 kN/m3ϕ=35°0C=0FOS=3

Q: 5. A column carrying a load of 750 kN is to be founded on a square footing at a depth of 2 m below…

A: We have to determine what will be the size of the footing if a factor of safety of 2.5 is…

Q: Determine the allowable soil bearing capacity of a frictionless soil for a 6 ft wide square footing,…

A: Given: Width of footing, B = 6 ft Depth of footing, D = 2 ft Cohesion, C = 2000 lb/ft2 Friction…

Q: A pad footing of dimensions 1.2 m by 2.5 m applies a surface pressure of 425 kPa. The pad footing is…

A: Given: The dimension of the footing is 1.2 m x 2.5 m. The surface pressure is 425 kPa. The thickness…

Q: The shallow foundation shown below measures 2 m x 3 m and is subjected to a centric load and a…

A: Solution: Shallow foundation measure=2×3 meB=0.2 meL=0.3 mdepth of foundation=30°Factor of…

Q: A foundation is constructed in a soil with the following parameters: c' = 5.0kN/m? y = 18.5 kN/m³ Ø'…

A: The given data is: B=2 m L=3 m C'=5 KN/m2 Q=3000 KN M=300 KN-m calculating eccentricity:…

Q: A square foundation must withstand an allowable load of 1805 kN reliability of 3. With the given…

Q: (5) There is a strip footing with a width of 2 m and a buried depth of 1.5 m. The foundation soil is…

A: The Ultimate Bearing capacity is calculated by Terzaghi theory.

Q: 775 kN Water table y = 17 kN/m c' = 0 1.75 m 4'= 32° BX B Ysat = ³ 19 kN/m c' = 0 4' = 40°

A: Given data Unit weight FOS Depth of footing Square footing To find Dimensions

Q: Task 3 (a) An isolated footing(pad) of RCC is to be designed for a column carrying a dead load of…

Q: A square footing, 1.7 m x 1.7 m, is to be founded at a depth of 1.4 m below the ground surface of a…

A: Ultimate bearing capacity The maximum load that can be supported without failing is known as the…

Q: Que a) A square foundation is 2.5 m * 2.5 m in plan. The soil supporting the foundation has an…

Q: A strip footing foundation 1 m wide is constructed in the slope of a hill whose surface inclination…

A: Given data:

Q: square footing is proposed to be constructed on the silty sand layer as shown in Figure Q2. If the…

A: γ - The soil is prone to failure by means of shear prior to any other mode of failure. The shear…

Q: A machine foundation has a base dimension of 4m x 8m and has weight of equal to 4.6 times weight of…

Q: Example 5 A square foundation (B * B) has to been constructed. Assume yd = 16.5 kN/m, Ysat = 18.55…

A: Given data γd=16.5 kN/m3γsat= 18.55 kN/m3Df= 1.22 mD1=0.61 mQall=667.2 KN ϕ=34° Nc=…

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: We have been given the following information:

Q: Using Terzaghi theory, determine the ultimate bearing capacity of a strip footing 1.5m wide resting…

Q: According to the form and assumption of reliability coefficient 4, it is desirable to determine the…

A: Given data Depth Cross section Unit weight Angle of internal friction Eccentricity I will use…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Suppose that you are to design a foundation with a depth of 1m. It was also observed that the groundwater table is located 0.4m from the ground. Design a rectangular footing that can carry a gross weight of 5kN. Use a factor of safety of 2.5. Present your chosen length to width ratio.
A square foundation is 1.5 m by 1.5 m in plan. The soil properties supporting the foundation have a friction angle of 28° and c = 15.2 kPa, unit weight = 19.8kN/m3• The depth of the footing is 2.0 m. Factor of safety is 3. Using Terzaghi's Bearing capacity equation, determine the design load on the foundation.
Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The distance between the two column loads L3 = 13.5 ft. The proximity of the property line at the left edge requires that L2 = 3.0 ft. The net allowable soil pressure is 2500 lb/ft2. Determine the breadth and length of a rectangular combined footing.
Using the general bearing capacity equation, what is the factor of safety for a foundation system that includes a 5 ft square footing at a depth of 4 ft carrying 120 kips at a 10 degree incline from vertical. c’=0. φ= 28º. γ = 100 lb/ft3. The water table is deep and is not expected to affect foundation performance.
The square footing shown below must be designed to carry a 294 kN load. Use Nc = 57.8 ; Nq = 41.4 and N? = 41.1. a.) Using Terzaghi's capacity formula, determine the width B of the square footing with a factor of safety of 3.0
A square footing 2.8 m X 2.8 m is built on a homogeneous bed of sand of density 18 kN/m3 and ϕ = 36o. If the depth of foundation is 1.8 m, determine the safe load that can be applied on the footing.
A column carrying a load of 750 kN is to be founded on a square footing at a depth of 2m below the ground surface in a deep clay stratum. What will be the size of the footing if a factor of safety of 2.5 is considered? Pertinent soil parameters are saturated unit weight of 18.5kN/m^3 , cohesion of 30 kPa and angle of internal friction of 18°. The groundwater is at the base of the footing but is expected to rise to the ground level during the rainy seasons.
A long footing, 1 m wide, has its base inclined 10° from the horizontal. The footing bears on the surface of a soil for which drained shear tests show a cohesion of 24 kPa and an angle of internal friction of 25°. The soil rigidity index value is 50. What load acting normal to the foundation base can be imposed if a factor of safety of 3 is used with the extended general bearing capacity equation?
Solve Problem 2 using the general bearing capacity equation Problem 2) A 1.5 m wide square footing is placed at 1 m depth within the ground where c = 10 kN/m², varphi' = 25 ^ 0 and 18 kN/m³. Determine the ultimate bearing capacity of the = footing using Terzaghi's bearing capacity equation. What is the maximum column load that can be allowed with a factor of safety of 3.0?
Determine the ultimate bearing capacity of a 1.3 m wide strip footing foundedat a depth of 1m below the ground surface. Soil parameters are φ′ = 36° c′ =10 kPa, and γ = 18 kN/m 3.
A machine foundation has a base dimension of 4m x 8m and has weight of equal to 4.6 times weight of the engine. Find the maximum weight of the engine to be mounted if the safe bearing pressure of soil is 211 kpa
A square footing 2.5 m X 2.5 m is built on a homogeneous bed of sand of density 19 kN/m3 having an angle of shearing resistance of 36o . The depth of foundation is 1.5 m below the ground surface. Calculate the safe load that can be applied on the footing with a factor of safety of 3.