Answered: Short circuit test on a single phase…

Short circuit test on a single phase transformer is performed to determine_____________ a. Magnetizing reactance b. Equivalent resistance c. Hysteresis losses d. No-load current

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.52P

See similar textbooks

Related questions

Q: Explain the open circuit test on single phase transformer.

A: Open circuit test :- It is carried out at rated frequency & rated voltage to determine the core…

Q: A certain single-phase transformer with full load copper loss and core-loss is loaded at full load.…

Q: How many types of winding in distribution transformers? What is the impact of each type on…

A: There are three types of windings: Single Helical Winding. Double Helical Winding. Disc-Helical…

Q: A typical single-phase transformer has a certain value of voltage regulation when connected to the…

Q: Why it's improctical carry out actual load test on large rating transformer

A: When a huge transformer is fully loaded, it can carry a lot of current and voltage. As a result,…

Q: A I0 kVA, single-phase transformer has a turns ratio of 12:1 and is supplied from a 24 kV supply.…

Q: From the topic of insulation resistance testing of a transformer, what specific precaution needs to…

A: This question is from "Power System And Protection". Under which we are going to study about…

Q: B/ Short answer questions 1- What is the function of instrument transformers? 2- What are the…

A: In this question we will write about instrument transformers, core type and shell type…

Q: Why are the low voltage winding short-circuited and high voltage excited during the short-circuit…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: Why do we represent leakage flux in a transformer by inductive reactance? 2. What will happen if…

A: In the transformer, the magnetic flux is produced by both the primary and secondary winding…

Q: What is the difference between two transformer with same voltage level and same rating current, but…

A: The transformer is a static electrical device that changes the voltage or current from one level to…

Q: In experiment :(separation of iron losses in single-phase transformer ),K1 belonging with hysteresis…

A: Given: Separation of iron losses in single phase transformer K1 belonging with the hysteresis K2 for…

Q: What's The relation between turn ratio current ratio annd voltage ratio(if it exists) for single…

A: The transformer is a static device that steps up or steps down the voltage depending upon the turn…

Q: For grounded systems, the _ for the service and the system bonding jumper for separately derived…

A: The equipment grounding conductor connections at the source of separately derived systems are done…

Q: A 50 MVA 230/115-kV, Δ-Y three-phase connected power transformer has a per unit resistance of 0.015…

A: Transformer is a static electrical device which transfers power from one circuit to another circuit…

Q: Answer the following questions 1. What physical and construction characteristics impact the value of…

A: Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: A certain single-phase transformer with full-load copper loss and core loss is loaded at full load.…

Q: What are the objectives of implementing a short circuit test on a single phase transformer?

A: Given What are the objectives of implementing a short circuit test on a single phase transformer

Q: 4. What do you mean by transformer connection Ydl and Dy11?

Q: 1-which side is short cct.in short cct. test ? why? 2- Draw the exact equivalent circuit of the…

A: Answer(1) A short circuit test is conducted to find out variable losses in the transformer. So, to…

Q: Determine the load sharing in MVA for each transformer. Draw the parallel transformer diagram for…

Q: Three single-phase two-winding transformers, each rated 25 MVA, 54.2/5.42 kV, are connected to form…

A: The explanation is as follows.

Q: Question 1 The shell type transformer has more leakage flux compared to core type transformer True…

A: The leakage flux in core type transformer more than that of shell type transformer .Because the core…

Q: What are the reasons for using transformer oil in power transformers and why are mineral oils…

A: The explanation is as follows.

Q: The per-unit system calculations method eliminates the need for explicit voltage-level conversions…

A: in the per-unit system each voltage is represented in terms of its base value

Q: difference between single phase and three phase transformer?

A: The transformers in an electrical system are used to convert the high potential to low potential or…

Q: transformer the core loss is 100 watt at 40 Hz and 72 watt at 37 Hz, then eddy current and…

A: In this question , we have to find out Eddy current losses and hysteresis losses...

Q: Power transformer divided into two categories which are dry type and oil-immersed transformer, with…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: Which transformer is used for welding application? Explain the operation in detail with diagram.

A: Need to find which transformer is used for welding application

Q: at happens if one phase of a 3-phase transformer fails?

A: Primary delta connected and secondary star connected: If the primary (delta) side loses one phase of…

Q: / Short circuit test on a single phase transformer is performed to determine_____________ a.…

A: Given that Short circuit test on a single phase transformer is performed to determine_____________

Q: TRUE or FALSE: If a transformer is loaded from full-load value to half-load value, then the amount…

Q: What is the definition of zero sequence impedance in transformer? What is the benefit of zero…

A: Transformer: A device which transfer a electrical energy from one circuit to another circuit…

Q: The shell type transformer has less leakage flux compared to core type transformer O True False

A: In this question ,we have to write that shell type transformer has less leakage flux or not compared…

Q: What conclusions we come up with after doing open circuit test on single phase transformer

A: For open circuit test of transformer excite any one winding of transformer at rated voltage and…

Q: Sketch a basic transformer structure. Identify and labelled the core, primary winding and secondary…

A: The correct solution is given below

Q: a) Discuss two (2) advantages and disadvantages of using three single-phase transformers instead of…

A: NOTE: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: During the load test of single-phase transformer, when the secondary terminal voltage increases, the…

Q: When the similar terminals of high voltage and low voltage windings of a transformers are diagonally…

A: A transformer is used to either up or down the voltage level. It can also be used to provide…

Q: Why are single-phase distribution transformers made whit the low-voltage winding in two sections? A-…

A: Single-phase distribution transformers made with the low-voltage winding in two sections to minimize…

Q: 12.a. Comparing the transformer cores of core-form and shell-form transformers shows that the a.…

A: Solution of question (12.a): Four options are given, we need to choose the correct option. The…

Q: (b) In a transformer test, data from short circuit and open circuit tests of a 75-kVA, 4600-230V,…

Q: What is the Influence of the manner the core coil assembly of the transformer on calculations of…

Q: Q2. (a) Explain what is per unit system? What are the advantages of per-unit computations? Prove for…

A: PU system: Per Unit system is a quantity expression system used in an electrical power system which…

Q: Explain the Difference between Single Phase & Three Phase transformers with a Comparison Chart. What…

A: In this question we will find difference between single phase and three phase...

Q: A 36/240 V phase transformer, belonging to a phase measured from the no-load (idle) run and…

A: transformer ration is 36/240 V OC test performed on LV windings SC test performed on HV windings

Q: 1- What are the advantages of Transformer Tests? 2- Why is the high voltage winding of single phase…

A: advantages of transformer tests why is high voltage winding of single phase transformer is kept open…

Q: transformer on no-load has a core-loss of 70 W, draws a current of 2.5 A (rms) and has an induced…

Q: Calculate the iron loss and copper losses of each transformer for full load condition in back to…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Short circuit test on a single phase transformer is performed to determine_____________ a. Magnetizing reactance b. Equivalent resistance c. Hysteresis losses d. No-load current

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The leakage reactance of a three-phase, 300-MVA,230Y/23-kV transformer is 0.06 per unit based on its own ratings. The Y winding has a solidly grounded neutral. Draw the per-unit equivalent circuit. Neglect the exciting admittance and assume the American Standard phase shift.
The ratings of a three-phase, three-winding transformer are Primary: Y connected, 66kV,15MVA Secondary: Y connected, 13.2kV,10MVA Tertiary: connected, 2.3kV,5MVA Neglecting resistances and exciting current, the leakage reactances are: XPS=0.09 per unit on a 15-MVA,66-kV base XPT=0.08 per unit on a 15-MVA,66-kV base XST=0.05 per unit on a 10-MVA,13.2-kV base Determine the per-unit reactances of the per-phase equivalent circuit using a base of 15 MVA and 66 kV for the primary.
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.
What should be the focus of transformer preventive maintenance efforts?
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
For developing per-unit equivalent circuits of single-phase three-winding transformer, a common Sbase is selected for all three windings and voltage bases are selected in proportion to the rated voltage of the windings (a) True (b) False
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer has a 1-ohm equivalent leakage reactance and a 5000-ohm magnetizing reactance referred to the high-voltage side. If rated voltage is applied to the high-voltage winding, calculate the open-circuit secondary voltage. Neglect I2RandGc2V losses. Assume equal series leakage reactances for the primary and the referred secondary.
The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) False
In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.