Short Problem: Given a parallel RLC circuit comprised of the following element: 94.42-ohm resistor, ideal inductor with reactance of 60.84 ohms; and a capacitor with reactance of 15.03 ohms. Compute for reactive power in VArs given an ac voltage source of 100 cis 0 volts. Give only the absolute value.

Short Problem: Given a parallel RLC circuit comprised of the following element: 94.42-ohm resistor, ideal inductor with reactance of 60.84 ohms; and a capacitor with reactance of 15.03 ohms. Compute for reactive power in VArs given an ac voltage source of 100 cis 0 volts. Give only the absolute value.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

A transmission line has a reactance of 1 Pu is operating at Vs = Vr = 1 Pu. The generator is connected at source end which is delivering 0.5 Pu of active power and the transmission line is compensated with a series capacitance of 0.5 Pu. Find the load angle with series capacitance compensation ?
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage V and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 R. Vcoil = 22.4 V, VR= 20 V and V = 36 V. find the resistance and inductance of the coil. please use reference photo
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load of impedance ? = (4 + ?3) Ω. We want to know: a) the active, reactive and apparent power consumed by the load. b) the power of a capacitor that must be installed in parallel with the load to raise its power factor to 0.97 delayed.
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.
what is the mutual inductance in ohms (or the mutual inductive reactance ) between the two mutually-coupled inductors? if circuit to the left of load Z is converted into its Thevenin's equivalent, what would be the magnitude of ZTh in ohms? what is the phase angle of ZTh in degrees? what would be the phase angle of VTh in degrees? what would be the magnitude of VTh in volts if E = 120 V?