Situation 2: A steel plate 8 mm thick is to be embedded in a horizontal concrete slab and is used to anchor a high-strength vertical cable 12 mm in diameter as shown. The diameter on the hole on the plate is 20 mm. Assuming that P = 10 kN, determine the safest minimum dimensions a and b as the width of the plate and the depth of embedment, respectively. Consider the following design parameters: P Allowable stresses: : 250 MPa 5 kPa Normal stress of steel Bonding stress of steel and concrete Note: Neglect the stress between the concrete and the bottom face of the plate. 8 mm A. Dimension a (mm) 20 mm-dia. B. Dimension b (mm) C. What is the factor of safety for the anchorage of the steel plate in the concrete slab if a = 50 mm and b = 90 mm?

Situation 2: A steel plate 8 mm thick is to be embedded in a horizontal concrete slab and is used to anchor a high-strength vertical cable 12 mm in diameter as shown. The diameter on the hole on the plate is 20 mm. Assuming that P = 10 kN, determine the safest minimum dimensions a and b as the width of the plate and the depth of embedment, respectively. Consider the following design parameters: P Allowable stresses: : 250 MPa 5 kPa Normal stress of steel Bonding stress of steel and concrete Note: Neglect the stress between the concrete and the bottom face of the plate. 8 mm A. Dimension a (mm) 20 mm-dia. B. Dimension b (mm) C. What is the factor of safety for the anchorage of the steel plate in the concrete slab if a = 50 mm and b = 90 mm?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Estimate the transverse tensile strength of the concrete in Problem 12.6.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
A high-strength steel band saw, 24 mm wide, runs over pulleys 800 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 280? Assume E = 230 GPa. Answer must %3D be in mm.
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X