SITUATION 2 (For this situation, there are no choices but you can input your answers ingoogle forms later)Calculate the following if the amount of flow is 1.26m³/s, the 80% efficient pump delivers1073kW, and the turbine is 92% efficient.EL. 120.50C-1100.60m-diameter360mEL 77.90C-1100.60mdiameter45.60mP556m14. Compute for the energy given by the pump15. Total Head Loss

Given, Q = 1.26 m3/s np = 80% P = 1073 kW

SITUATION 2 (For this situation, there are no choices but you can input your answers in google forms later) Calculate the following if the amount of flow is 1.26m/s, the 80% efficient pump delivers 1073kW, and the turbine is 92% efficient. EL. 120.50- -110 0.60m diameter 360m EL 77.90 C-110 0.60m diameter 45.60m 556m

SITUATION 2 (For this situation, there are no choices but you can input your answers in google forms later) Calculate the following if the amount of flow is 1.26m/s, the 80% efficient pump delivers 1073kW, and the turbine is 92% efficient. EL. 120.50- -110 0.60m diameter 360m EL 77.90 C-110 0.60m diameter 45.60m 556m

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter14: Ocean Thermal Energy Conversion And Ocean Salinity Gradient Energy

Section: Chapter Questions

Problem 14P

See similar textbooks

Similar questions

Q No. 3: A six-centrifugal pumps delivers 0.1 m3 /s against a total head of 480 m. What is its specific speed if it routes at 1450 rpm? What type of impeller would you recommended for the pump? Draw velocity triangles for centrifugal pump at inlet and outlet. Drive expressions for power input, power output and efficiency for Francis turbine using flow velocity triangles. Note : Need Neat And Clear Solution on Urgent Basis. Please Solve According To Statement Of Question.
A pump is used to raised water to a reservoir through 1000 m. long of 20 cm diameter with Cw of Hazen-William's Equation equal to 100. If the pipe is to be replaced with a new one having the same length but with a diameter of 25 cm and Cw= 120, determine the power save if the flow is to be maintained at 75liters per second. Draw the approximate EGL and HGL
9.The pump shown delivers 115 li/s of oil, sg = 0.84, toreservoir D at elevation 72 m. The energy lost in thesuction line is 3.2 J/N and in the discharge line is 7.6 J/N. a.Compute the total head added by the pump. b.How many kW does the pump supply the system? c.If the pump is 85% efficient, how much power does it need?
A pump is used to raised water to a reservoir through 800 m. long of 20 cm diameter with Cw of Hazen-William’s Equation equal to 110. If the pipe is to be replaced with a new one having the same length but with a diameter of 25 cm and Cw = 130, determine the power save if the flow is to be maintained at 100 liters per second. Draw the approximate EGL and HGL.
pls answer asap for my hydraulics course. A 30 cm diameter pipe is connected by a reducer to a 10 cm diameter pipe. Points 1 (on the 30 cm diam.) and 2 (on the 10 cm diam.) are along the same elevation. The pressure at 1 is 250 kPa. The flow is 30 liters per second and the energy lost between 1 and 2 is equivalent to 20 kPa. Compute the pressure at 2 if the liquid flowing has a specific gravity of 1.50.
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
Q2: Water is flow by arate = (v/( “7— /20) m¥/s , the water is still stable due to using a pump as shown in figure below. A pipe of rectangular cross sectional area of dimension (10 *20 ) cm is used to connect the two reservoir, friction factor for the pipes(£=0.02), if K value in the entrance and in the exit are 0.1 and 1 respectively. Calculate the pump power:- ElL15m Water EL10m Water = o cotanantwe *10 = 50 m——
A reservoir A with elevation 30m connected with a pump to rise the water into two reservoirs B and C 90m and 60 m respectively the amount of flow from J to B is equal 0.11 m/sec use the following data to determine the flow in each pipe and the power of the pump: LAJ 450 m, DaJ = 300 mm, LJB= 300 m, DJB = 200 m, Q JB = 0. m'/sec, LJc 600, D Jc = 150 mm,f (all Pipes) 0.02
If the flow of 0.10 m3/s of water (mu = 1.31 x 10-3 Pa.s) is to be maintained in the system shown, what power must be added to the water by the pump? The pipe is made of steel and is 15 cm in diameter. Neglect minor losses. TV
Calculate the required pump power since the velocity of the water in the pipe is v=1.91 m/s pwater=1000kh/m^3 μ=1.307x10^-3
For water supply of a town, water is pumped from a river 4km away into a reservoir. The maximum level difference of river and reservoir is 20m. Town population is 50,000 and per capita water demand is 120 lpcd. If the pumps operate for a total of 8hrs and pump efficiency is 60%, calculate pump B.H.P Assume friction factor as 0.0075 and pipe velocity as 2m/s and maximum daily demand as 1.6 times avg. daily demand.
Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.