Situation 20: The figure shows a precast plain concrete beam simply supported on ab --baFileHomeInsertD유 ShareX Cutspanof 3m.P Find -e CopyGiven:Sac ReplacePaste* Format PainterB Concrete unit weight =23.5kN/m³d.A Select -Clipboarda=200mmd=200mmEditingb=150mme=150mmc=500mmf=150mme67. Determine the weight of beampermetera. 2.85 kN/mb. 2.94 kN/mc. 3.94 kN/md. 4.14 kN/mwwC68. What is the allowable load on the beam if the cracking moment is 27 kN-ma. 21.15 kN/mb. 21.06 kN/mc. 19.86 kN/md. 20.06 kN/mSituation 21: A square tied column carries a factored load of 2800KN. It will be designed using material strengths fc'=27MPand fy=345MPA. Assume p=0.0269. Determine the minimum required dimension of the column.b. 450 mma. 400 mmc. 500 mmd. 550 mm70. Determine the number of o25mm vertical bars required.a. 8 barsb. 9 barsc. 10 barsd. 11 barsPage 7 of 1022 of 4146 wordsEnglish (United States)& Accessibility: Investigate160%ENG10:26 amamazonwR888US06/03/2022to

Columns are structural members which carry compression loads transferred from the beams and slabs.…

Situation 21: A square tied column carries a factored load of 2800KN. It will be designed using material strengths fc'=27MPa and fy-345MP.. Assume p-0.02 69. Determine the minimum required dimension of the column. b. 450 mm a. 400 mm c. 500 mm d. 550 mm 70. Determine the number of 625mm vertical bars required. a. 8 bars b. 9 bars c. 10 bars d. 11 bars

Situation 21: A square tied column carries a factored load of 2800KN. It will be designed using material strengths fc'=27MPa and fy-345MP.. Assume p-0.02 69. Determine the minimum required dimension of the column. b. 450 mm a. 400 mm c. 500 mm d. 550 mm 70. Determine the number of 625mm vertical bars required. a. 8 bars b. 9 bars c. 10 bars d. 11 bars

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Bucket: 8.5 lbBucket + concrete: 58.7 lbVolume: 0.265 ft3Density of Concrete: _____________lb/ ft3ASTM DESIGNATION: _____________
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use ASCE 7: Load Combination 1.2D+1.6L
GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS.
Determine the development length required in bar diameter for the epoxy-coated top bars of the beam with 6 - #9 longitudiinal bars, bw = 14", side and bottom cover = 2.5", spacing between bars is 4.5" o. c., normal concrete with f'c = 4 ksi, fy = 60,000 psi. Assume Ktr = 0. Express your answer in whole number.
The cross section of a reinforced concrete beam is shown below .( 5 - No . 10 bars )are designed as the bottom bars and No. 3 stirrups as the vertical reinforcement . Considering a clear cover thickness = 1.5 in , sketch the layout of reinforcement and show bar spacings per AC1318-19 . Assume maximum aggregate size = 1 in and the minimum required effective depth of bottom bars = 20 inches .
A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP
1. Concrete Hollow Block 200mm H x 400mm L x 150mm thk. per piece and Laying 8 layers x 4.5 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.80 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters A = 7.20m3 b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% N = 93 pcs c) How much mortar or grout is required in CHB laying? In cubic meters Answer: 0.5562 m3 d) How many bags of cement is needed if Class B Mixture is required? WF=3% Answer: 7 bags Answers are already given, solutions are needed.
A short (assume no buckling) 4x8 wood column (actual dimensions are 3.5" x 7.5") is placed in a testing device and loaded until it fails due to crushing. If the ultimate load was 19,725 pounds, what is the column's ultimate/crushing stress, in psi? Round to the nearest psi, and do not include commas or units in your answe r
concrete : C20 steel : S420 h=550 mm hr:100 mm b=750 mm bw=350 mm d'=40 mm steel rebars in top : 5Φ26 steel rebars in bottom : 5Φ26
5. A doubly reinforced rectangular beam has 3 - 20 mmɸ compression bars and 6 - 28 mmɸ.The breadth and overall depth are 410 mm and 650 mm respectively. Use 10 mmɸ stirrups,40 concrete cover, fc’ = 20.7 MPa, and fy = 345 MPa. Calculate the following(a) d (b) As’ (c) cbalance(d) a (e) fs’ (f) Cc(g) Cs(h) Abalance(i) check if compression steel yields (fs’ > fy)(j) design strength of the beam ( ? Mn)
QA Fora flow rate of 300 iter/second ata velocity of 1.3 meters/secand, design a seamless. steel Take factor of safety of 2.5, Longitudinal efficiency ofjoint, 1 = 0.50, and intesnal pressure= 4 Nl