SITUATION 3: A shaft ABCD is subjected to torques of 1,093 N-m at B and 1,620 N-m at C acting in the same direction. Consider the properties ofeach segment below:SegmentLength (m)Diameter (mm)Shear Modulus (GPa)АВ2.52485ВС4.28789CD3.25979If the supports A and D are fixed and unyielding, determine:A. The stress of each segment (MPa)B. The angle of twist from points A to C (rad)

Answered: Image /qna-images/answer/1596ebe1-66ac-4e08-b996-6ce99e68b92b.jpg

SITUATION 3: A shaft ABCD is subjected to torques of 1,093 N-m at B and 1,620 N-m at C acting in the same direction. Consider the properties of each segment below: Length (m) Diameter (mm) Shear Modulus (GPa) 24 Segment АВ 2.5 85 ВС 4.2 87 89 CD 3.2 59 79 If the supports A and D are fixed and unyielding, determine: A. The stress of each segment (MPa) B. The angle of twist from points A to C (rad)

SITUATION 3: A shaft ABCD is subjected to torques of 1,093 N-m at B and 1,620 N-m at C acting in the same direction. Consider the properties of each segment below: Length (m) Diameter (mm) Shear Modulus (GPa) 24 Segment АВ 2.5 85 ВС 4.2 87 89 CD 3.2 59 79 If the supports A and D are fixed and unyielding, determine: A. The stress of each segment (MPa) B. The angle of twist from points A to C (rad)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
Q.1 A structure is supported by braces each of which transfersa load P = 160 kips to the base of a column as shown infigure. A cap plate at the bottom of the brace distributesthe load P to four flange plates through a pin to twogusset plates. Diameter of Pin and thickness of flangeplate and gusset plate are provided in figure. Determine(a) The average shear stress in the pin.(b) The average bearing stress between the flange plates andthe pin.(c) The normal axial stress in gusset plate. Assume thatgusset plate is 4 inch wide. Note: Please answer the section c as well
The 115-mm-diameter steel shaft is subjected to the torques shown. T1 = 14 kN-m, T2 = 2 kN-m, T3 = 2 kN-m. Determine the angle of twist (degrees) of the end B. Use L1 = 0.75 m., L2 = 0.53 m., L3 = 0.69 m. Shear modulus = 71 GPa.
The compound shaft shown consists of a solid shaft AB made ofbronze [G = 40 GPa], and a solid shaft BC made of steel [G = 85 GPa].The compound shaft is subjected to torques TB = 700 N.m at point B,and TC = 200 N.m at point C, acting in opposite directions.[LAB = 900 mm, LBC = 1200 mm, dAB = 35 mm, dBC = 25 mm]Determine (a) the internal torques in shafts AB and BC, (b) the shearstresses in shafts AB and BC, and (c) the angle of twist at point C.
The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at each section. Assume G = 75 GPa. P=74 1.5P= 1.5(74) = 111 kNm 3P= 3(74)= 222kNm
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.
The Channel section is used as a purlin placed on top of trusses with spacing of 4 m and slope 1V to 4H. The purling are supporting a total uniform load of 24 kN/m. Properties of Channel: Sx = 119 x 10^3 mm^3 Sy = 87 x 10^3 mm^3 Compute the maximum bending stress if supported by sagrods at third points. Round your answer to 2 decimal places.
the circular bar 20m in diameter is bent into a semicircle with a mean radius of 600mm. givern P=1462N and F=800 N. 1. compute the vertical reaction at A in kN a. 886 b. 712 c. 933 d. 1232 2. compute the axial force in section a-a in kN. e. 400 f. 1266 g. 731 h. 693 3. compute the bending moment in N-m in section a-a. i. 284 j. 187 k. 667 l. 348
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures. (b) Redo problem (a) by using the bending moments over support A and B as the redundant forces. (c) Repeat problem (a) if there are support settlements of 8mm, 5mm and 2mm at A, B and C respectively. Given E=200GPa, I=107mm4 .