Situation 4: The uniform 50 kg plank in the figure is resting on rough surfaces A and B. The coefficients of static friction are shown in the figure. If an 80 kg man starts walking from A towards B. Compute the: = 0.2- A 5 m B -H₂=0.5 40° 1. reaction at A. 2. reaction at B. 3. distance x when the plank will start to slide.

Situation 4: The uniform 50 kg plank in the figure is resting on rough surfaces A and B. The coefficients of static friction are shown in the figure. If an 80 kg man starts walking from A towards B. Compute the: = 0.2- A 5 m B -H₂=0.5 40° 1. reaction at A. 2. reaction at B. 3. distance x when the plank will start to slide.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
The support B of the structure shown in Figure settled by 0.7 in. Determine all reactions using slope-deflection equations. Use E = 30,000 ksi and I = 240 in4.
10. Vertical Forces P & F in the figure produces a resultant of 500KN and a counter clockwise couple C of 250 KN-m. Find the magnitude of force P.
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. Determine the following;a. Reaction at A.b. Constant C1.c. Slope at L/3.d. Deflection at L/3.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
A stepladder consisting of two legs pinned together at C is resting on a rough floor. Will a 800 N worker be able to change the light bulb if he is required to climb to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. The coefficient of static friction at Aand B is 0.48.
Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is μs = 0.2.
For the simply supported beam carrying the concentrated load P = 176 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 2.34 m, E = 11.24 GPa , and I =1749035mm4.
Block B weighs 200N and block C weighs 100N. See Figure4. Determine the weight of block D and the required angle θ for equilibrium
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. Where: Q=2 T=6
Problem 2) The beam shown in Figure 2 – B is loaded with a 20 kN concentrated load and a 12 kN/muniformly distributed load, determine the following:a) The moment of inertia about the neutral axis.