What the requirements  for the Plumbing Design for water supply? What the requirements  for Plumbing Design for drainage systems? What the requirements  for acoustical control in buildings? What are some types of Mechanical System Design in buildings? Kindly answer all the questions. Thank you.

Q: Find the density of liquid whose specific gravity 1.221

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: 4. To monitor turbidity and chloride concentrations of incoming flow, an engineer designed a…

A: The given data is shown below: Operating velocity=13 m/s & 8 m/sPeak flow=9.5 MGD

Q: A triangular open channel has a vertex angle of 90° and carries flow at a critical depth of 0.30m…

A: Given data- Triangular open channel- vertex angle =90ocritical depth yc=0.30 mTo Find-The discharge…

Q: thank

A:

Q: A two-lane national highway passing through rolling terrain has horizontal curve of 450 m radius.…

A: Given- 2 Lane National Highway- Radius of curve R=450 mSpeed V=90 kmphwheel base L=6.1 mpavement…

Q: A grit chamber of rectangular cross-section is to be designed to remove particles with diameter of…

A: Given data- Diameter of particles d=0.25 mmG=2.70settling velocity Vs=2.5 cm/swidth of chamber…

Q: amine the plan of an interior bay of an office building shown. The floor is 8-in nforced concrete.…

A: We will assume the value of dead load and live load woring on the bay. Then using the conditions of…

Q: A roadway sign weighs 7.4 kN and is supported by a structural pipe that has an outside diameter of…

A: Answer  (a) Calculation of Normal and shear stresses at H Normal stress at H is given by resultant…

Q: Problem 1. Calculate the area between the offsets using Simpson's One-Third Rule. Chainage (m) 0…

A:

Q: A concrete beam of rectangular cross-section of size 120mm (width) and 200mm (depth) is prestressed…

A: Given- concrete beam with rectangular cross-section- dimensions of beamb=120 mmd=200 mmprestressing…

Q: Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy…

A:

Q: what are the significance of specific gravity and Blaine fineness tests

A: Specific gravity  The correct definition of specific gravity (sg) is the ratio of a substance's…

Q: The variation of air density at the standard pressure as a function of temperature is given in the…

A: Given values: T1 = 27° C, Density = D1 T2 = 33° C, Density = D2

Q: I'm sorry but the explanation is so hard to understand, I cannot follow the calculations

A:

Q: PROBLEM 2 Sketch the moment diagram by method of superposition with respect to point E. 20lb/ft A…

A:

Q: A fire hose nozzle directs a steady stream of water of velocity 50 m/s at an angle of 45° above the…

A: Given- steady stream water velociy=50 m/sangle=45og=9.81 m/s2It is needed to find the maximum height…

Q: A 2-m-long pin-ended column of square cross section is to be made of wood. Assuming E= 13 GPa, oal =…

A: Given data, A squre cross section column, L= 2m E= 13GPa Fos= 2.5  Psafe = 100kN Determine:- size of…

Q: Compute/Derived the following: a. wall shear b. wall moment c. Reaction d. Deflection at midspan…

A: "Since you have posted a question with multiple subparts , we will solve first three for you. To get…

Q: olve moj and  the tabulatio

A: degree of static indeterminacy, Ds = no. of members + no. of unknown support reactions - 2* no. of…

Q: Select the answer that most nearly gives the axial force on member ad from the real structure in…

A: The given figure is shown below:

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

A:

Q: A concrete beam of rectangular cross-section of size 120mm (width) and 200mm (depth) is prestressed…

A: Given data  Width of beam (B) = 120 mm  Depth of beam (D) = 200 mm  Effective force (P) = 150 KN…

Q: Using suitable examples, discuss the difference between the Static efficiency and the Dynamic…

A: Static efficiency and dynamic efficiency are two names for the same thing. Dynamic efficiency allows…

Q: Activity 2: Consider the following immediate preceding activity table. Draw the network and…

A: Given data:- ES X EF LS Duration LF ES=Early start EF=Early finish LS=Late start  LF=Late…

Q: Problema 1: La cercha de la figura está sometida a una fuerza vertical P = 9 kN actuando en la junta…

A:

Q: A smooth flat plate is in a parallel flow stream. The ratio of the drag over the upstream half of…

A:

Q: An aircraft is flying in level flight at a speed of 200 km/h through air (density, p = 1.2 kg/m³,…

A:

Q: Compute/Derived the following: a. wall shear b. wall moment c. Reaction

A: "Since you have posted a question with multiples subparts we will solve first three for you .To…

Q: Problem 2. Calculate the area of the closed traverse or field in square meters (using coordinate…

A:

Q: The speed-density relationship of a highway is given as u= 100-0.5k where, u = speed in km per hour,…

A: given- speed density relation- u=100-0.5k

Q: BC, CD AND DE are 2m in length.  all members act at right angles sketch the bending and torsional…

A: we divide each section, and using equilibrium equations we balance the forces and moments in each…

Q: A wastewater treatment plant treats a wastewater at a flowrate of 10 million liters per day. The…

A:

Q: Compute the following: a. wall shear b. wall moment c. Deflection at mid-span d. the maximum…

A: As per the guidelines we are supposed to answer only three subparts,. Kindly repost for other…

Q: Problem 1 Given: Mass of moist soil Volume of soil Dry mass of soil Specific Gravity (Gs) 305 g 166…

A:

Q: the minimum length of the chamber (in m, in integer)

A: Given data, Agrit of rectangular cross-section is to designed to remove particles,Diameter,d=0.25…

Q: Four measurements of distance were recorded as 352.45, 352.04, 351.89, and 353.12 meters and given…

A: Given:Measurements:X1=352.45 with W1=2X2=352.04 with W2=5X3=351.89 with W3=1X4=353.12 with W4=8

Q: Is materials property data needed for Graphene Coating in Construction generated by experiment or…

A: This type of procedure is mainly done for increasing the strength of the structure. As it improves…

Q: A 2m thick coal seam at a depth of 150m below ground surface is planned for extraction using 5.0m…

A:

Q: Find the value of m so that the given function y = xm is a solution of the given differential…

A: Given,  y = xm is the solution of the given differential equation,   xy" + 2y' = 0 and, x2y" -7xy'…

Q: 3. The unit weight of a soil is 100 lb/ft³. The moisture content of this soil is 20% when the degree…

A: Given : Weight of soil = 100 lb/ft3 Moisture content = 20 % degree of saturation = 55% To find : A )…

Q: 1. Four forces are applied to point P as shown. Knowing that F₁ = 50 lb, F2 = 20 lb and F4 = 70 lb,…

A:

Q: 2m jokN 2m 25kN ļ 2m Fa solve for maximum Reflection using Double-Integration

A: Let,RA=Vertical reaction at support A in upward direction.RB=Vertical reaction at support B in…

Q: 500 kgf auf 800 kgf/m wit, 1111111 1m

A: Given data:

Q: Flow rate of a fluid (density = 1000kg/ m³) in a small diameter tube is 800 m³/ s. The length and…

A: Given- discharge Q=800 m3/s density ρ=1000 kg/m3 Length L= 2 m Diameter D=0.5 mm pressure drop = 2…

Q: A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of…

A:

Q: Problem 3. Calculate the maximum depth, h, behind the concrete dam below that maintains a factor of…

A: Let Weight of dam be W1 ; W1 = 8 × 30 × (Unit weight of concrete) W1 = 8 × 30 × (165) W1 = 39600…

Q: P= 356 kN P= 178 KN A D G 6 m B E H 7 m C 6 m

A: Solve the frame using portal frame method: Shear force in column: Top Storey: ∑fx=0 P+2P+P=356…

Q: autocad

A: Answer : We can draw the isometric view from given orthographic view in Autocad using the following…

Q: An activated sludge process (ASP) is designed for secondary treatment of 7500 m³/day of municipal…

A:

Q: Using Galerkin's method, derive the stiffness matrix for the following beam element, which has an…

A: Given: Vx=a1x5+a2x4+a3x3+a2x2+ax+a6 The shape functions are N1, N2, and N3.