Situation: A column with circular ties shown carries a dead load of 1000 kN and a live load of 520 kN. Use f'c-28 and fy=420 MPa. U=1.2D+1.6L. Which of the following most nearly gives the safe diameter of the column if p = 0.0185? a. 340 mm b. 380 mm C. 400 mm d. 450 mm Which of the following most nearly gives the required minimum diameter of main bars if the diameter of column is 400mm? 25 mm 32 mm C. 28 mm d. 20 mm a. b.

Situation: A column with circular ties shown carries a dead load of 1000 kN and a live load of 520 kN. Use f'c-28 and fy=420 MPa. U=1.2D+1.6L. Which of the following most nearly gives the safe diameter of the column if p = 0.0185? a. 340 mm b. 380 mm C. 400 mm d. 450 mm Which of the following most nearly gives the required minimum diameter of main bars if the diameter of column is 400mm? 25 mm 32 mm C. 28 mm d. 20 mm a. b.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q#3. An aluminium strut 14 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER. THANKS
QUESTION1) Figure Q1(a) show a simply supported beam of length L = 4.8m is and built for placing Machine and Magnum frame. The combined weight of the machine is approximated by uniform load 90kN/m along x3 = 2.4 m. For of the design, its assumed that the column framed located at a distance x1 and x2 = 0.8m and resulting concentrated load P1 and P2 exerted oneach beam is taken as 150kN and 150kN, respectively. The cross section of beam show as in Figure Q1(b). (a) Determine the bending stress at point a and the maximum bending stress of the beam (b) By referring Figure Q1(a) and consider section n-n, determine the maximum shear stress and the shear stress at point a.
q2: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.705 m, b = 1.821 m, and L= 4 M.For a load of P = 117 kN, determine thedisplacement of joint F. Unit should be in mm
Question 14 A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 8-20-mm-diameter (28) longitudinal bars equally distributed to the shorter sides of the column. Use f’c = 21 MPa and fy = 415 MPa. 46. Calculate the required spacing of 10-mm-diameter ties. s = mm 47. Calculate the nominal axial strength of the column in, Pn = kN. (rounded to the nearest whole number) 48. Calculate the maximum ultimate axial load the column can carry, Pu = kN. (rounded to the nearest whole number)
A 550mmx800mm column reinforced with 12 pcs of D20mm (3 bars each on outer ends). The column carries an ultimate load of 3500kN at an eccentricity 325mm. Assuming concrete strength and steel strength to be 25MPa and 420MPa respectively. Take clear cover to be 40mm and diameter of ties to be 10mm. Determine the balanced compression depth, mm. Determine the balanced moment, kN-m. What is the design strength, kN.
Design a tie column to carry an axial dead load of 600 kN and an axial live load of (1.6X1+2.6X2)kN. Given material properties are fy= X2 MPa, f’c=X1 MPa (X1=124.6 , X2=385)
21 A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 12-ϕ20 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa. Calculate the nominal axial strength of the column in kN. 6,985 5,588 5,938 5,239
USE 3 decimals; DRAW FREE BODY DIAGRAMS A 9-m simple beam is carrving a uniform load or 25 kN/m over the entire beam with two-point loads of 15 kN at 1.5 m from both ends. If E = 200 Gpa and | = 0.000332 m^4, determine the following using the Double Integration Method:a.) Midspan deflectionb. Deflection at 1.5 m from the eft reaction
A square, tied column 410 mm wide is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 25 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only. Correct Answer: 1,513.80 ± 1.5
-6,00 Design a short square tied column to carry a factored axial design load Pu of 750 kips an a factored design moment Mu of 250 ft.-kips. Place the longitudinal reinforcing uniformly in the four faces. Use f, = 5000 psi and fy = 60,000 psi. o. Then P 350-1.9 h2 1.86 30 ao
Q#3. An aluminium strut 14 ft long has a rectangular cross section 1.5 in by 3 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3 in dimension; and as fixed column about an axis perpendicular to 1.5 in dimension. Determine the safe central load with a factor of safety of 2.5 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it.
Determine support reaction. P=800 lb , a=5 ft b=9 ft