Situation B. | The figure on the above-right shows a system of 3 steel wire, each with an area 0.05 in?, used to lift a load W=1,500 Ib. Their unstressed lengths are 74.98 ft, 74.99 ft, and 75 ft. E= 29x10° psi. Note: Do not round off during calculations, use the store functions of your calculator. 3) Determine the stress in the longest wire (psi) 4) Determine the stress in the shortest wire (psi)

Situation B. | The figure on the above-right shows a system of 3 steel wire, each with an area 0.05 in?, used to lift a load W=1,500 Ib. Their unstressed lengths are 74.98 ft, 74.99 ft, and 75 ft. E= 29x10° psi. Note: Do not round off during calculations, use the store functions of your calculator. 3) Determine the stress in the longest wire (psi) 4) Determine the stress in the shortest wire (psi)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.7 in from the top of the beam on section 2.05 feet to the right of B if P = 1080 lb, Q = 4215 lb, w = 1.08 in, L = 8.26 in, b = 3.97 in, and h = 1.25 in. Round off the final answer to two decimal places
The constant wall thickness of a tube with the elliptical cross section shown is 0.12 in. What torque will cause a shear stress of 6000 psi? please write legibly, thanks
help! please write the correct answer. no long explanation needed! upvote will be given! Mechanics of Deformable Bodies A. WHAT IS THE NORMAL STRESS IN MPa at point C at the center if P = 74.8 kN. if Compressive add add a minus sign in final answer. 2 decimal places. B. If P = 70 kN, what is the normal stress at point A in MPa? (2 decimals)
Q2) a) Define the following surface tension, , pitot tube , barometer ,Reynold number b) A bourdon pressure gauge records a pressure of 100 KN/m2 .The barometer reading is 761 mm Hg, what is the absolute pressure in 1) KN/m2 2) Bar 3) mm Hg 4) pascal
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the top of the beam on section 2.47 in to the right of B if P = 1042 lb, Q = 4278 lb, w = 1.1 in, L = 7.37 in, b = 3.82 in, and h = 0.73 in.
3.Figure (a) shows a rigid bar that is supported bya pin at A and two rods, one made of steel and theother of bronze. Neglecting the weight of the bar,compute the stress in each rod caused by the 50-kN load, the following data：
Q#1: A block is shown in figure. Consider a compressive load is applied (one at a time) on all corners (A, B, C and D) of the block. This will cause each corner to be in a different state of stress under the action of load at different location. Discuss the effect of load on each corner under changing load locations. It is mandatory to consider the effects of direct stresses and bending stresses. (1
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
For the beam shown, calculate the bending stress at a point 70 mm. from the top of the beam. P = 59, a = 233, b = 296 Round your answers to 2 decimal places.
Refer to the photo provided and please make sure your handwriting is readable a = 1.01 m b = 2.02 m c. 1.505 m d. 4.505 m P1 = 6.06 kN P2 = 24.04 kN 1. Compute the resultant reaction at I in kN. 2. Compute force member DE in kN 3. Compute normal stress in member CE in kN/m2 if the value of the area is A mm2.
Given the state of stress shown, determine the normal stress (in MPa) acting on the inclined plane a-a if S = 93.19 MPa, N = 42.03 MPa, and A = 36.4°. Express final answer in four decimal places.
Determine the normal stress (in psi) at point D for the b=2.1-in. by h= 6-in. beam shown below if X = 6.97 in, P = 9468 lb, and F = 2714 lb. Round off final answer to four decimal places.