SOLUTION IS NEEDED How much total energy in Joules is generated in a machine gear if its temperature increases by 50 C°. It's parts are made of 0.20 kg of iron and 0.15 kg of copper. Round-off your answer to the nearest whole number. Do not type the unit of your final answer. * Ccopper = 390 ; Ciron = 450 kg.Cº kg.Cº

SOLUTION IS NEEDED How much total energy in Joules is generated in a machine gear if its temperature increases by 50 C°. It's parts are made of 0.20 kg of iron and 0.15 kg of copper. Round-off your answer to the nearest whole number. Do not type the unit of your final answer. * Ccopper = 390 ; Ciron = 450 kg.Cº kg.Cº

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter1: Temperature And Heat

Section: Chapter Questions

Problem 84P: A 0.250-kg aluminum bowl holding 0.800 kg of soup at 25.0 is placed in a freezer. What is the final...

See similar textbooks

Similar questions

In a showdown on the streets of Laredo, the good guy drops a 5.00-g silver bullet at a temperature of 20.0C into a 100-cm3 cup of water at 90.0C. Simultaneously, the bad guy drops a 5.00-g copper bullet at the same initial temperature into an identical cup of water. Which one ends the showdown with the coolest cup of water in the West? Neglect any energy transfer into or away from the container.
When heal transfers into a system, is the energy stored as heat? Explain briefly.
If the refrigerator door is left what happens to the temperature of the kitchen?
A 100-g piece of copper, initially at 95.0C, is dropped into 200 g of water contained in a 280-g aluminum can; the water and can are initially at 15.0C. What is the final temperature of the system? (Specific heats of copper and aluminum are 0.092 and 0.215 cal/g C. respectively.) (a) 16C (b) 18C (c) 24C (d) 26C (e) none of those answers
One method of converting heat transfer to doing work is for heat transfer into a gas to take place, which expands, dong work on a piston, as shown in the figure below. (a) Is the heat transfer converted directly to work in an isobaric process, or does it go through another form first? Explain your answer. (b) What about in an isothermal process? (c) What about in an adiabatic process (where heat transfer occurred prior to the adiabatic process)?
In car racing, one advantage of mixing liquid nitrous oxide (N2O) with air is that the boiling of the "nitrous" absorbs latent heat of vaporization and thus cools the air and ultimately the fuel-air mixture, allowing more fuel-air mixture to go into each cylinder. As a very rough look at this process, suppose 1.0 mol of nitrous oxide gas at its boiling point, 88 , is mixed with 4.0 mol of air (assumed diatomic) at 30 . What is the final temperature of the mixture? Use the measured heat capacity of N2O at 25 , which is 30.4J/mol . (The primary advantage of nitrous oxide is that it consists of 1/3 oxygen, which is more than air contains, so it supplies more oxygen >to bum the fuel. Another advantage is that its decomposition into nitrogen and oxygen releases energy in the cylinder.)
One method of getting a tight fit, say of a metal peg in a hole in a metal block, is to manufacture the peg slightly larger than the hole. The peg is then inserted when at a different temperature than the block. Should the block be hotter or colder than the peg during insertion? Explain your answer.
On a trip, you notice that a 3.50-kg bag of ice lasts an average of one day in your cooler. What is the average power in watts entering the ice if it staffs at 0 and completely melts to 0 water in exactly one day?
You pour coffee into an unlidded cup, intending to drink it 5 minutes later. You can add cream when you pour the cup or right before you drink it. (The cream is at the same temperature either way. Assume that the cream and coffee come into thermal equilibrium with each other very quickly.) Which way will give you hotter coffee? What feature of this question is different from the previous one?
If you add boiling water to a cup at room temperature, what would you expect the final equilibrium temperature of the unit to be? You will need to include 1he surroundings as pan of the system. Consider the zeroth law of thermodynamics.
During the isobaric expansion from A to B represented below, 130 J of heat are removed from the gas. What is the change in its internal energy?
Is a uniform-temperature gas more or less orderly than one with several different temperatures? Which is more structured? In which can heat transfer result in work done without heat transfer from another system?