SOLVE FÖR THE FOLLOWING USING PRESSURE-PRISM 1. A tank is filled to a depth of 5 feet of water and is 8 wide by 10 feet long. Determine the hydrostatic force acting on the horizontal bottom and on the vertical ends of the tank. 2. The gate shown is rectangular and has dimensions 6 m by 4 m. What is the reaction at point A? Neglect the weight of the gate. 3 m Hinge Atmospheric pressure Stop 30 6 m Water

SOLVE FÖR THE FOLLOWING USING PRESSURE-PRISM 1. A tank is filled to a depth of 5 feet of water and is 8 wide by 10 feet long. Determine the hydrostatic force acting on the horizontal bottom and on the vertical ends of the tank. 2. The gate shown is rectangular and has dimensions 6 m by 4 m. What is the reaction at point A? Neglect the weight of the gate. 3 m Hinge Atmospheric pressure Stop 30 6 m Water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Obtain the gage pressure at the center A of the pipe shown. Neglect the surface tension effects. Liquid 1, sg=1.5. Liquid 2, sg=3.2, h1=15cm; h2=30 cm; h3=75 cm.
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Hydraulics ProblemAn open horizontal tank 1.5m high 2m wide and 5m long is full of oil with a specific gravity of 0.9. It is accelerated in the direction parallel to the longer length at 2.3 m/s2 a. What is the force acting on the wall of the tank with the shortest depth in KN? b. If the acceleration is increased by 0.88 m/s2. Determine the volume of oil that spilled out the tank?Note: Draw free-body diagram and used 4 decimal places
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. a. The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c. The hydrostatic force due to water. d. The net hydrostatic force acting on the gate Fnet
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. A.) The hydrostatic force due to linseed oil F1. B.)The hydrostatic force due to castor oil F2. C.)The hydrostatic force due to water. D.)The net hydrostatic force acting on the gate Fnet
. A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The sucLon pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diameter and 150 m long. if the velocity in the pipe is 3 m/s, the fricLon factor of the pipe 0.008, and the pump and motor efficiencies 85 % and 92 %, respecLvely. See Figure Q6.1. Calculate:(a) Gauge pressure at the pump's inlet (at C) (10)(b) Gauge Pressure at the pump's outlet (at D) (10)(c) input power to motor (5)
Water is stored in a tank with an inclined panel AB whose dimensions are 2m long by 1.6m wide. The manometer indicates a gage liquid height of z = 1.2m. a. Determine the pressure (in kPa) at B. b. Determine the pressure (in kPa) at A? c. Apply the pressure prism concept in determining the force (in kN) exerted on side AB. d. At what distance from A (along the surface of panel AB) is the hydrostatic force acting? Your answer should be in centimeters.
The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.58-in.-diameter piston of the hydraulic-cylinder unit AB.Assume a = 5 in., b = 33 in., c = 17 in., e = 36 in., and 26°. C=? LB p=? Lb/in^2
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center ?, the spool has a larger radius ?=0,17 and an inner radius ?=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: ?? μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
5.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the vertical component of the hydrostatic force on the submerged curved section of the gate. Use unit weight of water 9.80 kN/m^3. fluid mechanics
For a vertical rectangular gate, one side has linseed oil (0.939) and the other has two fluids - castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism to calculate the magnitude and direction of the following when z = 20ft. A. The hydrostatic force due to linseed oil F1 B. The hydrostatic force due to castor oil F2 C. The net hydrostatic force acting on the gate Fnet D. The hydrostatic due to water