Solve the distributed load problem given using both the calculus and the composite areas methods

Q: Find the Shear Moment Diagram of the following problems using

A:

Q: 2. The half section of an arc is under a uniformly varying load. If the weight of the arch is 50,000…

A: The centroid of a body is the point where all sides have equal volume. The centre of mass of a solid…

Q: Use the virtual work method to determine the horizontal and vertical components of the deflection of…

A:

Q: Find the Shear Moment Diagram of the following problems using ONLY AREA METHOD.

A: Explanation: The stepwise procedure to draw SFD and BMD using area method is shown in the following…

Q: value of the slope at the free end is

A: Given, Flexural rigidity of a cantilever beam is constant.If load P and bending moment PL2 are…

Q: A cantilevered beam is loaded as shown. The cross section at the wall is shown, with points of…

A: givencantilever beam as shown belowF=22kNb=50mmd=50mm

Q: Q2 Figure Q2 shows the cantilever beam being fixed at support A. (a) Construct the free body diagram…

A: given: (a) free body diagram of the member;

Q: Solve using Double integration method and determine the max deflection

A:

Q: Q.2) Draw the shear force and bending moment diagrams for the distributed load and two reaction…

A: draw the shear force and bending moment diagram.

Q: A cantilever beam of length 2 m carries the point loads as shown in Fig. Draw the shear force and…

A:

Q: find the reaction at roller support at B find the reaction at the external pin support at A Find…

A: The free body diagram of the beam is given below,

Q: Solve magnitude P using method of sections if DG is -15kN

A: Calculated magnitude P using method of sections if DG is -15 kN .

Q: 6.18 Two uniformly distributed loads are placed symmetrically on the simply supported beam.…

A: we have to determine the value of maximum value of EI

Q: The beam shown carries a uniformly distributed load of 2 kN/m along span BC. The beam is supported…

A: Solution: ∑MB = 0 ⇒ 2 x 6 x 3 = RC x 6 ⇒ RC = 6 kN ∑Fy = 0 ⇒RB + RC = 2 x 6 = 12 kN ⇒ RB = 12 - RC…

Q: the correct shear force diagram for the beam is:

A: Hello, since you have uploaded multiple question and did not specify which question is needed to be…

Q: 2. Two 10-in 15.3-lb channels are welded together as shown in the figure. Compute the value of Ix.…

A:

Q: Q14 Find the load .if the load distance 3m and effort distance 10m and effort3300N Effort Pivot Load

A:

Q: 2. Compute the midspan value of Ely for the beam loaded below 600 N/m 1 m 3 m 2 m R1 R2

A:

Q: A simply supported beam is loaded as shown in the Figure. The corresponding SFD and BMD would be: 20…

A:

Q: Q.2) Draw the shear force and bending moment diagrams for the distributed load and two reaction…

A: First calculate the reactions then draw the Shear force diagram and bending moment diagram

Q: Find the section modulus for a beam of circular cross section with the diameter of 70mm. The section…

A:

Q: a) If the spring is cut by half of its length and is loaded by the same load, compute the…

A:

Q: problem 3 Find the Shear Moment Diagram of the following problems using ONLY AREA METHOD.

A:

Q: Problem 5 The beam shown below is subjected to unfactored service live loads, PL and w. Neglect the…

A:

Q: A beam is loaded as shown in the figure. What is the location of the concentrated load from point B?

A: Consider the diagram of the beam as shown below. Here W1 is the triangular load and the W2 is the…

Q: The steel propeller shaft ABCD carries the axial loads shown in Figure (2). Determine the hange in…

A:

Q: Q14 Find the load .if the load distance 3m and effort distance 10m and effort=300N

A:

Q: What does the application of the moment area method require?

A: This is also known as Mohr's theorem. The moment area method is used to find the deflection of the…

Q: Draw the shear force diagram for the given beam along with calcukation and accurate values in the…

A: Shear force diagram represents shear force at every section of the beam. Shear force at any…

Q: find the longitudinal strtain experienced by the strut it width is 8mm and height is 20mm

A:

Q: Compute the deflection at C uperposition method.

A: Deflection at a point by superposition method :- It is the summation of deflection at a point due to…

Q: Use the slope deflection method by using the graphical method to calculate deflections and draw…

A:

Q: the beam shown by the moment-area method.

A: To determine maximum deflection

Q: Solve the following problems. Be sure to show your work. Answer without work shown will receive no…

A: Drawing equivalent load diagram. and calculated magnitude and location of the resultant force with…

Q: The magnitude of the maximum deflection is

A: Given; A cantilever beam of the length L is subjected to amoment M at the free end.The moment of…

Q: Draw the internal shear force and bending moment diagram usin the Graphical Method (or the…

A:

Q: A 2120 lb weight is attached to a 3.4-ft-wide gate that can pivot about the hinge The weight is at a…

A:

Q: Find the section modulus for a beam of circular cross section with the diameter of 90mm. The section…

A: Diameter(D)=90mm

Q: 6) Compute the value of El y at the right end of the given beam. Use the Double Integration Method.

A: Calculate the reaction at the support, RA+RB=400×3+400RA+RB=1600   ............. (1) Taking the…

Q: 100 kN %3D 200 kNm 2 m- 2 m-

A: Shear force is defined as the summation of all the internal forces either to the left of the section…

Q: A simply supported beam is loaded as shown. Use E = 200,000MPa and I=150 x 106 mm4. Compute for the…

A: Given:  E = 200,000MPa and I=150 x 106 mm4. The beam is shown below:

Q: A Simply supported beam is Lm long and is subjected to a uniformly distributed load of q kN/m…

A:

Q: A beam (AB) is supported by a roller at B and a pin at A. It is subjected to the following uniform…

A:

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.