Solve the problem shown below. Each answer is worth equal credit. Show all necessary steps of your work clearly to obtain credit. Final answer must be to 3 significant figures and contain units and be in the box. Using P1= 6.0 kips, then determine the reactions and member forces of the truss. a) List reactions at A and K? (Use positive, +, to indicate a reaction that is up, to the right, and counterclockwise.) [30 pts] RAX: RAY: Rkx: Rky: b) Determine the member forces using either the method of joints or method of sections. (Include Units and the correct sign in the answer, (Use: '+'= tension, & '-' = compression) J H G 4 ft K FBC: FCJ:

Solve the problem shown below. Each answer is worth equal credit. Show all necessary steps of your work clearly to obtain credit. Final answer must be to 3 significant figures and contain units and be in the box. Using P1= 6.0 kips, then determine the reactions and member forces of the truss. a) List reactions at A and K? (Use positive, +, to indicate a reaction that is up, to the right, and counterclockwise.) [30 pts] RAX: RAY: Rkx: Rky: b) Determine the member forces using either the method of joints or method of sections. (Include Units and the correct sign in the answer, (Use: '+'= tension, & '-' = compression) J H G 4 ft K FBC: FCJ:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure 2: Given the below determine the bar force at AB. (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 2) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
Please show complete solution with formula and free body diagramA rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A load of W = 34 kN is lifted through a boom 'BCD' as shown in the figure. The boom makes an angle of 60 degrees with the vertical. Neglect the weight of the boom for this problem, L1 = L2 = 2.6 m. The pulley at 'D' is frictionless. d.) What is the vertical component at 'B' in kN? e.) Calculate the total reaction at 'B' in kN. *Round off in 4 decimal places. Thank you.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")
Figure 4: Determine the bar force at FN (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 4) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
Figure 3: Given the figure, determine the member that will be designed for maximum tension (Note: just write the member designation ex: AD) just indicate the two letters.
Determine the force in each member of the truss shown in (Figure 1). State if the members are in tension or compression. Take that P = 420 lb. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression. Given: angle to use is 36.9 degrees, FCD = 700lb FAD =-560lb Find: a) Determine the force in the member BC of the truss, and state if the member is in tension or compression. b) Determine the force in the member AC of the truss, and state if the member is in tension or compression. c) Determine the force in the member AB of the truss, and state if the member is in tension or compression.
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
If the flexural rigidity of the column is doubled, and length of the simply supported column is halved, then the strength of the column is increased to how many times
The system shown in the figure is subjected to a force of F = 509 N 1) Calculate the magnitude of the force on support B. Show all the complete free-body diagrams required to obtain this and all answers. This is the numerical answer you provide in this question. 2) Calculate the horizontal and vertical reactions at support A. Write your answer to the nearest integer. Don't forget the units. In an additional question you must upload a document with the procedure carried out to obtain your answer.
The assembly is made of A-36 steel cylinders. (Figure 1) Part A: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 220 kN is applied. Enter your answers in kilonewtons to three significant figures separated by a comma. Fa, Fd = ?