Hand written both parts fast plz..i'll give you multiple upvote asap 10.7 A steel pinion has 16 teeth of module 6 and rotatesat 600 r/min, driving a gear of cast-iron with a gear ratioof 3. The face width is 70 mm and the tooth form is 20°involute. (a) If the basic stress for the steel is 186 MPaand that for cast-iron is 55 MPa, calculate the safe powerthat can be transmitted; and (b) if 20° stub teeth had beenused, what safe power could be expected?[14,17kW; 16,49 kW]

Answered: Image /qna-images/answer/1f7d13d3-54c5-40b7-87ac-c62470408461.jpg

steel pinion has 16 teeth of module 6 and rotates 600 r/min, driving a gear of cast-iron with a gear ratio 3. The face width is 70 mm and the tooth form is 20° volute. (a) If the basic stress for the steel is 186 MPa nd that for cast-iron is 55 MPa, calculate the safe power at can be transmitted; and (b) if 20° stub teeth had been sed, what safe power could be expected? [14,17kW; 16,49 kW]

steel pinion has 16 teeth of module 6 and rotates 600 r/min, driving a gear of cast-iron with a gear ratio 3. The face width is 70 mm and the tooth form is 20° volute. (a) If the basic stress for the steel is 186 MPa nd that for cast-iron is 55 MPa, calculate the safe power at can be transmitted; and (b) if 20° stub teeth had been sed, what safe power could be expected? [14,17kW; 16,49 kW]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

See Figure P12–6. The shaft rotating at 310 rpm carries a spur pinion E having 36 teeth with a diametral pitch of 6. The teeth are of the 20°, full-depth, involute form. The pinion delivers 20 hp to a gear to the left as shown. Compute the torque delivered by the shaft to pinion E and the tangential and radial forces exerted on the shaft by the pinion. Include the weight of the pinion.
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G = 6,500 ksi] tubes, which have an outside diameter of 2.40 in. and a wall thickness of 0.1375 in. Segments (3) and (4) are solid 1.00-in.-diameter steel [G = 11,500 ksi] shafts. The shaft lengths are L1 = 58 in., L2 = 16 in., L3 = 16 in., and L4 = 28 in. The torques applied to the shafts have magnitudes of TB = 970 lb·ft, TD = 430 lb·ft, and TE = 170 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A.
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
XY=11 By examine the parameters given, evaluate the maximum power-transmitting capacity, based on AGMA bending strength for both gears.
A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion with 15 teeth. The overall ratio of the gearbox is 6:1 and the gearbox is transmitting a power of 6000W. If the factor of safetv is to be reduced to an absolute minimum acceptable value and the gears are to be made from a material with a Yield stress of 540 MPa, what is the face width of the gears (in mm) Express your answer in the form 21.00 ie with two decimal place an no units
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.
Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm long. Oneis solid but the other is hollow with an inside diameter of 40 mm. Both are made from steel. Compare the torsionalshear stress, the angle of twist, and the mass of the two designs if they are subjected to a torque of 850 N ·m.
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
A cast-iron pulley transmits 49 kW at 1,750 rpm. The shaft to which it is to be keyed is 44.4 mm in diameter. If the key width is 10 mm and allowable shearing and compression stresses are 151.6 MPa and 271.2 MPa, compute the length of the square key needed.
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut. A.Determine the diametral pitch, B. face width, C. and tooth numbers if the material is cast iron, class 25