STRENGTH OF MATERIALS (UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS IN 3 DECIMAL PLACES. NO LONG EXOLANATION NEEDED. BOX THE FINAL ANSWER) >Solve the MAXIMUM FELXURAL STRESS of the beam

Q: Air exits a turbine at 150 kPa and 150°C with a volumetric flow rate of 7,000 liters/s. Modeling air…

A:

Q: 2 kN 4 kN H —5 m→ B 4 kN G -5 m— с 5 kN D F 3 kN -5 m▬▬5 m– E 3 m 2'm

A:

Q: Consider a pipe-pipe configuration consisting of concentric steel tubes with an intervening…

A: Given Di1=150mmti=to=10mmDi2=250 mmho=500 W/m2Kks=35 W/mKkp=0.075W/mKhi=450 W/m2K

Q: A 1500cm³, four-stroke, four cylinder CI engine operating at 3000rpm produces 48kW of brake power.…

A: The given information in the problem is shown in the following attached image:

Q: Determine the resultant R (single equivalent force) of the three forces acting on the simple truss.…

A:

Q: 6 A circular area of radius, R = 5 m subjected to a uniformly distributed 380 kN/m². Determine the…

A: According to the given data R=5m z=3m r=0,1,3,5,7 m q=380kN/m2 We need to find Vertical stress…

Q: Determine the force in member BD of the regular pyramid with square base. The force is positive if…

A:

Q: A block of mass m, 2.40 kg and a block of mass m₂ = 5.90 kg are connected by a massless string over…

A:

Q: (a) 2 (b) 3 (c) 5 (d) 4 (e) 1 ? 2 3 4 5

A: Given: Top view is showing as the two rectangular block in second and third row of the grid. Front…

Q: For a given heat flux, the temperature gradient and the thermal conductivity are O A. twice the size…

A: This question is based on the concept of conduction.

Q: Carbon dioxide enters an adiabatic nozzle at 1400 K with a velocity of 60 m/s and leaves at 600 K.…

A:

Q: An engine parts is being tested with a load of 60000 lb. The allowable tensile stress is 10000 psi,…

A: Given data: loadP=60000 lballowable tensile stress =10000 psi=10000 lb/in2modulus of elasticity(E)…

Q: A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to an…

A: According to the given data D=50mm t=5mm d=D-2(t)=40mm P=10MPa F=20kN at an angle of 45 degrees to…

Q: Q.3. The figure shows a planar truss under the giving loading, held in static equilibrium by a pin…

A:

Q: Consider the composite wall below. The inner side of the wall is subjected to air flow at 430°C with…

A:

Q: How you find minimum drag and velocity from the equations

A: Given: The drag, D = ax+[b(mg)2/x]

Q: Same problem is considered here again using three equal length elements. Suppose that the strain…

A: Given Data :- Strain energy of element 1 ( u1) = 0.09 N.m Strain energy of element 2 ( u2) = 0.17…

Q: Report on the calibration of the pressure gauge 6:51 PM /

A: Pressure Guage: Pressure gauges are used to indicate pressure and used for pressure measurements.

Q: x1 L Figure 1: Cantilever beam. A cantilever beam of narrow rectangular cross-section of unit width…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 2. A water is flowing out of the pipe and nozzle when the pressure at point A is 55 kPa where the…

A: Given data  Diameter at A = 200mm  Pressure at 55 kPa  Find the velocity at A  Discharge coming out…

Q: a drop of water has a diameter of 2.5 mm. What is the surface tension in air if the pressure within…

A: Givend=2.5mm=0.0025m∆P=0.8kPa=800 Pa

Q: Please find the centroid and moment of Inertia around axis X and axis Y passing through of centroid…

A: Givenw=f=2cmD=14cmB=12cm

Q: Show complete solution. Units must be included in all calculations. All numerical values should be…

A:

Q: 4. A rope wrapped twice around a post will support a weight of 4037 N when a force of 58 N isexerted…

A:

Q: Required inf As the hollow steel shaft shown rotates at 165 rpm, a stroboscopic measurement…

A:

Q: Calculate the amount of heat in joules needed to increase the temperature of 350 g of water from 20…

A: According to the given data in the question m=350 gram T1=20°C T2=56°C We need to find Amount of…

Q: Problem 2. Consider a rod with radius c, subject to shear force V. Clearly show the Neutral Axis on…

A: Givenshear stress τ=VQItwhereV is shear forceC is radius of the section

Q: Small steel balls fall from rest through the opening at A at the steady rate of 2 per second. Find…

A:

Q: A beam is loaded and supported as shown below. Using the integration method, determine (a) The…

A:

Q: As shown in the figure below, a piston-cylinder assembly contains 20 g of air holding the piston…

A: The data given is, Mass of the air, ma = 20 g = 0.020 kg Initial temperature, T1 = 600 K Initial…

Q: Water is flowing through point 1 (D = 22mm) and point 2 (d = 17mm) in the above venture meter. What…

A: According to the given data D1=222mm D2=17mm Q˙=0.70zl/s We need to find P1-P2

Q: The exercise machine consists of a rigid bar, pin connected to the frame at A. As the man pushes up…

A: Given data  Stiffness = 500lb/ft.  Find the force applied vertically upward

Q: 2. A car starts from rest and travels 8 sec with an acceleration of a = 4-0.3t, then runs for 33 sec…

A: Givena=4-0.3t      when 0≤t<8v= constant    when 8≤t<41      ie. 33+8=41sa=-3.125 m/s2   until…

Q: Determine the force in member BD of the regular pyramid with square base. The force is positive if…

A: Draw the free-body diagram of the regular pyramid.

Q: Ships at sea undergo motion about their roll axis, as shown in Fig. The stabilizers can be…

A: Given data: Transfer function: θ(s)/TD(s) = 2.25/(s2 + 0.5s + 2.25)   To Find: the natural…

Q: ᴀ 3000 ʟʙ ᴀᴜᴛᴏᴍᴏʙɪʟᴇ (ᴄᴏɴꜱɪᴅᴇʀᴇᴅ ʀɪɢɪᴅ) ꜱᴛʀɪᴋᴇꜱ ᴛʜᴇ ᴍɪᴅᴘᴏɪɴᴛ ᴏꜰ ᴀ ɢᴜᴀʀᴅ ʀᴀɪʟ ᴛʜᴀᴛ ɪꜱ ᴀɴ 8 ɪɴ, 23ʟʙ…

A: Given data: A 3000 lb automobile strikes the midpoint of a guard rail The guard rail is an 8 in, 23…

Q: Determine by direct integration the centroid of the area shown

A: According to the given data y=acosπx2L  We need to find  Centroid of the cross-section of the…

Q: A projectile is launched from point O with the initial conditions shown. Determine the impact…

A: The x coordinate of the projectile motion is given by, x = v0×(cos θ)×t therefore, t = x/(vo×cos θ)…

Q: 2. A 1.2 mm diameter tube is inserted into an unknown liquid whose density is 960 kgm/m3, and angle…

A: Given data: h=5 mmd=1.2×10-3 mρ=960 kg/m3θ=15° Need to determine the surface tension of the liquid.

Q: 1. Determine the centroid of the area for the following. 100 mm 140 mm JE 140 mm 200 mm

A:

Q: 5 Discussion 1-Is the PCM method of transmitting synch. Information channel? Explain your answer…

A: Question 5 Part 1 PCM (Pulse Code Modulation) method does not typically transmit synchronization…

Q: Train A is traveling at a constant speed VA = 40 mi/hr while car B travels in a straight line along…

A:

Q: A wedge shaped bar, as shown below, is subjected to a tensile load, P. The width of the root and tip…

A:

Q: The 1.7-kg collar is at rest in position A when the constant force P is applied as shown. Determine…

A:

Q: 11. A 5 m long cylindrical rod with a radius of 5 mm is bent to form an angle of 8. This rod is made…

A: Given: Length of rod, L = 5 m Radius of rod, R = 5 mm or 0.005 m Young's modulus, Y = 200 GPa or…

Q: 1. 1107 A. B. 400 lb-ft C. C Si 160 lb -3 ft- A B 70 lb 34° The structure shown is fixed at A and is…

A: According to the given data A loading beam ABC  We need to find Reactions at point A

Q: Problem Statement Based on Problem 7-42 from the textbook. Determine the x, y, z components of force…

A:

Q: rovide explanation: 1). Explain why a bubble tends to float in air. What is the principle behind?…

A: A bubble floats in the air because it is less dense than the surrounding air. The principle behind…

Q: Consider the beam below with F = 9 kN. Neglect the thickness of the beam. F 4 3 5 LB -2 m -2 m- -2 m…

A:

Q: The inside design conditions for a conditional space are 19.5 degree C dry-bulb and 17.8 degree C…

A: Given: Dry bulb temperature of inside design condition, Td = 19.5°C Wet bulb temperature of inside…