The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (aj vetemine the maximum bending stresses (T & C) and absolute maximum transverse shear stress (b) Check if the beam is safe if the allowable bending stress (T&C) = 120 MPa and the allowable shear stress = 80 Mpa. W 4.0 m 4.0 m IT tw Section Properties: b=320 mm d = 350 mm tf-20 mm tw = 20 mm

The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (aj vetemine the maximum bending stresses (T & C) and absolute maximum transverse shear stress (b) Check if the beam is safe if the allowable bending stress (T&C) = 120 MPa and the allowable shear stress = 80 Mpa. W 4.0 m 4.0 m IT tw Section Properties: b=320 mm d = 350 mm tf-20 mm tw = 20 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.3.15P: A reinforced concrete T-beam (see figure) is acted on by a positive bending moment of M = 175...

See similar textbooks

Similar questions

A sandwich beam having steel faces enclosing a plastic core is subjected to a bending moment M = 5 kN · m. The thickness of each steel face is 1 = 3 mm with modulus of elasticity E = 200 GPa, The height of the plastic core is hp= 140 mm, and its modulus of elasticity is Ep= 800 MPa. The overall dimensions of the beam are h = 146 mm and h = 175 mm. Using the transformed-section method, determine the maximum tensile and compressive stresses in the faces and the core.
.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
A hollow box beam with height h = 16 in,, width h = 8 in,, and constant wall thickness r = 0.75 LiL is shown in the figure. The beam is constructed of steel with yield stress ty = 32 ksi. Determine the yield moment My, plastic moment A/p, and shape factor.
A reinforced concrete T-beam (see figure) is acted on by a positive bending moment of M = 175 kip-ft. Steel reinforcement consists of four bars of 1.41-inch diameter. The modulus of elasticity for the concrete is Ec= 3000 ksi while that of the steel is £s = 29,000 ksi. Let b = 48 im, rf = 4 in., bw=15 in,, and d = 24 in, Find the maximum stresses in steel and concrete, If allowable stresses for concrete and steel are o"ac = 1400 psi and tr^ =18 ksi, respectively, what is the maximum permissible positive bending moment?
A horizontal beam under bending has a maximum bending stress of 100 MpA and a maximum shear stress of 20 Mpa. What is the maximum principal stress induced in the beam.
A cantilever beam of cross section 90 mm.width 120mm deep Carrie's a UDL of 12KN/m. Over the entire length and a concentrated load of 15 KN at right end. find the bending stress in the beam, when the length of beam is 10 m.
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 18 cm as width, 27 cm as depth and thickness as 1 cm is subjected to a point load of 5 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 1 m. Solution: i) Reaction force at B = ________N ii) Reaction Force at A = ________N iii) The distance from B at which the shear Force value changes from "-" to "+" = ________m iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = ________Nm v) Moment of Inertia, I = ________m^4 vi) Maximum bending stress = ________N/m^2 vii) Bending stress at 1 cm from the top = ________N/m^2
Uniformly distributed load on a simple support beam with a length of 6 metersMaximum that occurs on the cross section when q is appliedIf bending stress is 337.5MPa,How many kN/m is the equal distribution load q?(However, the cross section of the beam is wide x height = 40mm x)100 mm.)
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 11 cm as width, 28 cm as depth and inner thickness as 1 cm is subjected to a point load of 5 N & 6 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 1 cm from the top =
A beam having a T shaped section is subjected to a vertical shear force of V = 10,000 N. The cross sectional dimensions are flange width, bf = 100mm, flange thickness tf = 25mm, gross depth of h = 200 mm and web thickness of 25 mm. Determine the maximum shear stress in the flange.
What is the minimum steel shear area (Av in sq.mm.) of a beam 300mm wide if fc'=21MPa and fy=340? let the spacing of stirrups be equal to 220mm Pls hand written solution
A simply supported beam AB = 9 m has a hollow rectangular cross-section with 13 cm as width, 20 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 8 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 2 m. i) Reaction force at B in (N)= ii) Reaction Force at A in(N)= iii) The distance from B at which the shear Force value changes from "-" to "+" in (m)= iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 1 cm from the top in (N/m^2) =