Study the heat treated steel workpiece shown in Figure A. Its dimensions are width w = 30 mm, height h = 50 mm, length / = 150 mm. The top surface of the workpiece is slimmed down with a material removal rate (MRR) of 2250 mm/min. %3D What is the depth of cut d within 1 minute in case you remove the material with slab milling?

Study the heat treated steel workpiece shown in Figure A. Its dimensions are width w = 30 mm, height h = 50 mm, length / = 150 mm. The top surface of the workpiece is slimmed down with a material removal rate (MRR) of 2250 mm/min. %3D What is the depth of cut d within 1 minute in case you remove the material with slab milling?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter1: Getting Started

Section: Chapter Questions

Problem 48PQ: In 2011, artist Hans-Peter Feldmann covered the walls of a gallery at the New York Guggenheim Museum...

See similar textbooks

Similar questions

A uniform density sheet of metal is cut into the shape of an isosceles triangle, which is oriented with the base at the bottom and a corner at the top. It has a base B = 49 cm, height H = 15 cm, and area mass density σ. a) Consider a horizontal slice of the triangle that is a distance y from the top of the triangle and has a thickness dy. Write an equation for the area of this slice in terms of the distance y, and the base B and height H of the triangle. b) Set up an integral to calculate the vertical center of mass of the triangle, assuming it will have the form C ∫ f(y) where C has all the constants in it and f(y) is a function of y. What is f(y)? c)Integrate to find an equation for the location of the center of mass in the vertical direction. Use the coordinate system specified in the previous parts, with the origin at the top and positive downward. d)Find the numeric value for the distance between the top of the triangle and the center of mass in cm.
In the data for A dependence of R (Table 2b), by what factor (multiplier) did the diameter D increase from the thinnest to the thickest wire? Show the ratio calculation in support of your answer. By what factor did the area A increase? Show calculation. Are these factors consistent with how area A and the diameter D are related? If D doubles, by what factor would you expect the cross-sectional area to increase? D diameter (cm) 0.0175 0.0255 0.0315 0.0415 A area (cm^2) 2.41x10^-4 5.11x10^-4 7.79x10^-4 13.5x10^-4 V(volt) 0.945 0.898 0.850 0.777 I (Amp) 0.0214 0.0410 0.0600 0.0903 R Resistance (Ω) 44.2 21.9 14.2 8.60
Imagine a very huge industrial metallic bucket is in the shape of the frustum of a right circular cone whose top and bottom diameters are 10 m and 4 m respectively and a height of 4 m. a) what is the curved surface area of the bucket? b) what is the volume of water if it’s to be filled to the brim if the thickness of the metal is 0.60 meters including the base?
A 4.00-m-long cylinder of solid aluminum has a radius of 2.00 cm. 1)If the cylinder is initially at a temperature of 5.00∘C, how much will the length change when the temperature rises to 30.0°C? (Express your answer to three significant figures.) 2)Due to the temperature increase, by how much (in %) would the density of the aluminum cylinder decrease? (Express your answer to three significant figures.) 3)By what percentage does the volume of the cylinder increase? (Express your answer to three significant figures.)
Grains of fine California beach sand are approximately spheres with an average radius of 50 m and are made of silicon dioxide, which has a density of 2600 kg/m3.What mass of sand grains would have a total surface area (the total area of all the individual spheres) equal to the surface area of a cube 1.00 m on an edge?
In 2011, artist Hans-Peter Feldmann covered the walls of a gallery at the New York Guggenheim Museum with 100,000 one-dollar bills (Fig. P1.48). Approximately how much would it cost you to wallpaper your room in one-dollar bills, assuming the bills do not overlap? Consider the cost of the bills alone, not other supplies or labor costs. FIGURE P1.48
f the density of air is 1.25 × 10-3 g/cc, what is the mass in kilograms of the air in a room that is 5.3 m long, 4.2 m wide, and 2.0 m high?
Grains of fine California beach sand are approximately spheres with an average radius of 50 pm and are made of silicon dioxide, which has a density of 2.6 x 103 kg/m3 What mass of sand grains would have a total surface area (the total area of all the individual spheres) equal to the surface area of a cube 0.8 m on an edge?
A surveyor uses a steel measuring tape that is exactly 75000m long at a temperature of 20 degree celcius? What is the length (in m) of the tape when them temperature is 35 degrees celcius? (in the image) The answer (in fundamental SI unit) is ___________ (type the numeric value only)
W A carpet is to be installed in a room of length 9.72 m and width 5.3 m. Find the area of the room retaining the proper number of significant figures.
Consider the equation a=6πb/q√17 relating the variables a, b and q. If a scientist does an expirment in which b is held constant, q is varied, and a is measured. A. What specifically about the graph would confirm the relationship? B. What is the theoritical slope of the line on the graph?
An engineer who is working on the heat transfer analysis of a house in English units needs the convection heat transfer coefficient on the outer surface of the house. But the only value he can find from his handbooks is 22 W/m2·K, which is in SI units. The engineer does not have a direct conversion factor between the two unit systems for the convection heat transfer coefficient. Using the conversion factors between W and Btu/h, m and ft, and °C and °F, express the given convection heat transfer coefficient in Btu/h·ft2·°F.