Substitute the value for s = 5 For the beam and loading shown. P = 20×S N, F = 10×S N, Q = 4xS N/m, (INA= 10.6x10 m). %3D Determine the following and showing your steps: (a) Find the centroid of the cross section. (b) Find the maximum tensile bending stress in the beam and its location from point A. (c) The shear stress at point H in the cross section. (At a distance of 4 m to left of support D).

Substitute the value for s = 5 For the beam and loading shown. P = 20×S N, F = 10×S N, Q = 4xS N/m, (INA= 10.6x10 m). %3D Determine the following and showing your steps: (a) Find the centroid of the cross section. (b) Find the maximum tensile bending stress in the beam and its location from point A. (c) The shear stress at point H in the cross section. (At a distance of 4 m to left of support D).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.8.1P: A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q =...

See similar textbooks

Similar questions

A C 200 x 17.1 channel section has an angle with equal legs attached as shown; the angle serves as a lintel beam. The combined steel section is subjected to a bending moment M having its vector directed along the z axis, as shown in the figure. The cent roi d C of the combined section is located at distances xtand ycfrom the centroid (C1) of the channel alone. Principal axes yl and yvare also shown in the figure and properties Ix1,Iy1and 0pare given. Find the orientation of the neutral axis and calculate the maximum tensile stress exand maximum compressive stress if the angle is an L 76 x 76 x 6.4 section and M = 3.5 kN - m. Use the following properties for principal axes for the combined section:/^, = 18.49 X 106 nrai4,/;| = 1.602 X 106 mm4, ep= 7.448*(CW),_r£ = 10.70 mm,andvf= 24.07 mm.
A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q = 3.0 kips/ft on a span of length L = 12 ft (sec figure). The dimensions of the cross section are q = 10.5 in., b = 5.81 in., t1= 0.510 in., and fw = 0.300 in. Calculate the maximum shear stress tjuly on cross section A—A located at distance d = 2.5 ft from the end of the beam. Calculate the shear stress rat point Bon the cross section. Point B is located at a distance a = 1.5 in. from the edge of the lower flange.
An overhanging beam ABC with a rectangular cross section has the dimensions shown in the figure. A weight W = 750 N drops onto end C of the beam. If the allowable normal stress in bending is 45 MPa, what is the maximum height h from which the weight may be dropped? (Assume E = 12 G Pa,)
A weight W = 4000 lb falls through a height h = 0.5 in, onto the midpoint of a simple beam of length L = 10 ft (see figure). Assuming that the allowable bending stress in the beam is = 18,000 psi and E = 30 x 10* psi, select the lightest wide-flange beam listed in Table F-l(a) in Appendix F that will be satisfactory.
Solve the preceding problem for a box beam with dimensions h = 0.5 m, h = 0.18 m, and t = 22 mm. The yield stress of the steel is 210 MPa.
Determine the plastic modulus Z and shape factor/for a W 12 x 14 wide-flange beam. Obtain the cross-sectional dimensions and section modulus of the beam from Table F-l(a) in Appendix F.
As shown in the figure below, determine the internal loadings at points D and. Consider the weight of the beamwhich is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
A beam having a tee-shaped cross section is subjected to equal 13 kN-m bending moments, as shown. Assume bf = 95 mm, tf = 25 mm, d = 165 mm, tw = 40 mm. The cross-sectional dimensions of the beam are also shown. Determine(a) the centroid location (measured upward from the bottom), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H (positive if tensile and negative if compressive).(c) the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section.
Consider the beam shown. Suppose that w1 = 600 N/m , w2 = 300 N/m . Follow the sign convention. A) Determine the internal normal force at point C. NC = ? B) Determine the internal shear force at point C. VC = ? C) Determine the internal moment at point C. MC = ?
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 40.4 ksi. Assume P = 51 kips, L1=6.6 ft, and L2=19.8 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 1.51 m, E = 11.77 GPa , and I =1679930mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU! image below for reference
Consider the beam section below where fc’ = 30 MPa, Es = 200 GPa, determine the bending stress of the steel section if M=180 KN-m in MPa. Express your final answer in two decimal places.