Superheated steam (s. fig. C) at a pressure of 300 bar and a temperature of 550 ℃ enters a turbine made up of two stages. Steam exits the first stage of the turbine at 35 bar and gets reheated at a constant pressure at 550 ℃. Each stage of the turbine has an isentropic efficiency of 80%. The isentropic efficiency of the pump is 85%. The pressure of the condenser is 10 kPa. (a) Sketch the cycle in a T-s diagram and calculate the enthalpy at each point of the cycle. (b) Calculate the flow rate of the working fluid if the power output of the turbine is 100 MW. (c) Calculate the thermal efficiency of the cycle. (d) Double check the result for the heat rejected in the condenser.

Q: A 90 cm pulley transmits 75 kW at 750 rpm. The arc of contact between the belt and pulley is 135…

A:

Q: 2 litre of petrol weighs 14N. Calculate the specific weight, density, specific volume and specific…

A: We have two liters of gasoline, which weights 14 N.In order to establish the specific weight,…

Q: A tempered glass window in an automobile requires two holes near the bottom edge, in order to attach…

A: In this problem, it is asking about the way to make holes during the manufacturing process in glass.…

Q: The lovely blue rectangle has a base of 290 mm and a height of 40 mm Use Mohr's Crde to determine…

A: Given: The base of rectangle, b = 290 mm The height of rectangle, h = 840 mm

Q: At a certain point in castor oil the shear stress is 0.216 N/m and the velocity gradient 0.216 s. If…

A: We know that the shear stress in castor oil is 0.216 N/m2 and the velocity gradient is 0.216 s-1 at…

Q: The lap joint is fastened with four 0.87-in.-diameter rivets. The working stress is 12.34 ksi for…

A:

Q: Briefly explain why placing a PVC pipe nipple between a black iron water pipe and a copper pipe…

A: Corrosion is a process of destruction of the metal. There are galvanic corrosion, metallic…

Q: Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa…

A:

Q: nine the magnitude and sense of the moment of F1 about point O. * m, counterclockwise '. m,…

A: Ans : 5.5 N-m counter clockwise

Q: Steam enters the turbine of a steam power plant, operating on Rankine cycle, at 10 bar, 300°C. The…

A: Since you have asked multiple questions in a single request we would be answering only the first…

Q: Please include a free body diagram Solve for: a) Normal strain in the x- direction −4.0 ×…

A:

Q: Design the hydraulic circuit for clamping and drilling operation shown in Figure 1. with the…

A: Given : To find : Hydraulic circuit

Q: For a 3RPS parallel manipulator shown in Fig. 1, draw the graph, and derive the adjacency matrix.…

A:

Q: Water is heated in an insulated, constant-diameter tube by a 7-kW electric resistance heater. If the…

A:

Q: An open circular cylinder of 20 cm diameter and 120 cm long contains water upto a height of 80 cm.…

A: Length of the container = 1.2 m Height of water = 0.8 m Diameter of container D=0.2 m N=400 rpm

Q: Figure Q2 shows a spool with a mass of 20 kg and a radius of gyration ko = 0.16 m. The 15 kg block A…

A: GivenM=20kgko=0.16mm=15kgω=8 rad/s

Q: A long and wide heated plate is maintained at uniform temperature. You have to calculate the average…

A:

Q: What factors would you consider in selecting materials for US coins?

A: Coins are made of metals that have been chosen for their long-term durability. Coins serve a…

Q: Ø 30 Ø62 342 -- 40 10 15 20 18/20 80 20 Draw the three (028

A:

Q: 3 m Find the rectangular representation of the force F, given that its magnitude 240 N. * DF=-135.76…

A:

Q: The assembly shown is supported by pin supports at A and B, and consists of four members connected…

A:

Q: Check if o = x –- y² + y represents the velocity potential for 2-dimensional irrotational flow. If…

A:

Q: Look up Pascal’s principle, state it in your own words, and tell how it was applied in the…

A: As per Pascal's principal, if an external pressure P is applied on an incomprehensible fluid then it…

Q: For the object shown in Fig. P2.92, calculate SA for neutral stability when submerged. 8 cm 1 cm I…

A:

Q: Knowing that the link lengths of the mechanism shown L-30mm, L,-49 mm, L-33 mm, L, - 101mm.…

A:

Q: Part A The rectangular plate undergoes a deformation shown by the dashed lines where D = 4 in. dj =7…

A:

Q: A belt is to transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at…

A: .Given:  power transmitted→P=50 KW=50000 W Diameter of the driving sheave→D1=10…

Q: Solve the following problem: One kilogram of water contained in a piston–cylinder assembly,…

A:

Q: The rigid beam of negligible weight is supported by a pin at O and two vertical rods. Find the…

A: Given: The load, P = 70 kips

Q: P

A:

Q: Express F, and F, as Cartesian vectors. F = 600 N F2 = 450 N 45° 30

A: Resolve the force onto X , Y and Z axis will gives the Cartesian coordinates form of vector

Q: Density of liquid is 850 kg/m Determine relative density and weight density of the liquid.

A: We know the density of liquid is 850 kg/m3, thus we need to figure out the liquid's relative density…

Q: II. Determine the degrees of freedom for regions U, V, X, Y in the Phase Diagram U X Temperature For…

A: Given : To find : Degrees of freedom

Q: #2: the condenser of Geothermal Heat Pump will be cooled by A pipe wit meter 3 cm buried in a soil…

A:

Q: 1) Consider the wave of small wave elevation in water of infinite depth. By linearization the water…

A: The wavelength of the wave is: λ=100 m The constant speed of the wave is: v=7 m/s

Q: A heavy-water-cooled research reáctor is fueled with natural- Im metal rods 0.9 in. in diameter clad…

A:

Q: . Consider the conveyor belt shown below. As the rollers turn at a constant rate, the top portion of…

A:

Q: Fresh water and seawater flowing in parallel horizontal pipelines are connected to each other by a…

A:

Q: block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in…

A:

Q: The axial load 296 kN applied to the lap joint is distributed equally among the three…

A:

Q: graph, and derive the adjacency matrix. Moving platform Fixed base Fig. 1 R

A:

Q: Instead of typing commands directly in the Command Window, a series of commands can be placed into a…

A: Given question: Instead of typing commands directly in the Command Window, a series of commands can…

Q: • Mechanically speaking, an oar is a beam, loaded in bending. • It must be strong enough to carry…

A: Given data Weight hung =W = 10 x 9.81 NDistance from Collar to point of maximum deflection = 2.05…

Q: For a normal axial-flow turbine stage with axial velocity at exit, it is given that both the flow…

A: Given Data: flow and loading coefficient =1.75 ϕ =1.4ψ=1.4 Equation of the flow in the rotor…

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP

A: The multiview projection of the given isometric view can be drawn as follows:

Q: Find the natural frequencies of transverse vibration of string of length 1 m resting on linear…

A:

Q: By applying a force F, a saline solution is ejected from the 16-mm diameter syringe through a 0.3-mm…

A:

Q: hat is the shear strain in radian if ?= 50 °? a. 0.75 b. 0.95 c. 0.873 d. 5/18 π

A: Given      Angle = 50o Find    Shear strain in radian

Q: If the collector current IC= 7.95mA and the emitter current IE=8mA, then alpha calculates out to be:…

A:

Q: The lap joint is fastened with four 0.83-in.-diameter rivets. The working stress is 14.55 ksi for…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.