Suppose a person wishes to lift a large rock with the lever. If the rock has a mass Of 250 kg and is located 50 cm from the pivot, and the person can put a force of 650 N Straight down on her end of the lover, what is the maximum distance from the fulcrum she has to be to lift the rock?

Q: If the torque required to loosen a nut on the wheel of a car has a magnitude of 40.0 Nm, what…

A: Given data:  Torque (τ) = 40 Nm Perpendicular distance (r) = 50 cm = 0.5 m Required Force (F) =?

Q: A tightrope walker is walking between two buildings holding a pole with length L = 14.0 m, and mass…

A:

Q: An 800-N billboard worker stands on a 4.0-m scaffold weighing 500 N and supported by vertical ropes…

A:

Q: A force 107 N is applied to a rigid body. If the moment arm with respect to a given point O is = 5…

A: Given: F→=10i^ N r→=5j^ N Introduction: The torque is calculated by taking the product of the force…

Q: At what angle to a door should one apply a force to produce the greatest torque? 0 30 45 90 O O

A:

Q: 2.15 A large wood beam weighing 800 N is supported by two posts as shown. If an unthinking man…

A: The Diagram for the given Question is:

Q: The cantilevered beam is supported at the fixed support A as shown in Figure Q3.1. 6 kN 130 1 30°…

A:

Q: A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square…

A: Gardener is holding the spade horizontally. This shows that weight of spade = force by gardner’s…

Q: A vault is opened by applying a force of 300 N perpendicular to the plane of the door, 0.70 m from…

A: Given data:  Force (F) = 300 N Perpendicular distance (r) = 0.70 m Required: Torque (τ)

Q: The drawing shows a rectangular peice of wood. The forces applied to corners B and D have the same…

A: Given,The length of the shortest side is ‘L’.The length of the longest side is ‘2L’.Let the third…

Q: A tightrope walker is walking between two buildings holding a pole with length L = 14.5 m, and mass…

A:

Q: We are going to look at having two hanging masses on the right: 1.50 kg at 0.30 meters from the…

A:

Q: The figure shows a bicycle wheel resting against a small step whose height is h = 0.130 m. The…

A:

Q: What three factors affect the torque created by a force relative to a specific pivot point?

A: we know that torque is the cross product of force and the perpendicular distance. Mathematically,…

Q: A wheel 3.2 ft. in diameter rolls up an incline of 16⁰. When the point of the contact of the wheel…

A:

Q: A uniform 1500-kg beam, 20.0 m long, supports a 15,000-kg printing press 5.0 m from the right…

A: Taking moment about P 1500g×10+15000g×15=FB×20FB=1500+1500×152g=1500×8×9.8=117600 N

Q: Which of the following is needed for a rigid body to be in equilibrium? (A) It must be stable. (B)…

A: When a rigid body is in equilibrium, then it does not have angular acceleration or linear…

Q: In the definition of torque ( T = r· F· sin(0) ), what does r represent? a) The entire length of the…

A: Given data: The torque due a force F τ = r.F.sin(θ)

Q: A bolt is tightened by applying a 60 N force to a wrench. If the magnitude of the torque is 120 Nm,…

A:

Q: A child with a mass of 23 kg sits at a distance of 4 m from the pivot point of a seesaw. Where…

A:

Q: Two fishermen are exerting a force of 200 N on a paddle while rowing in the middle of a lake. If the…

A:

Q: A lever is 5.0 m long. The distance from the fulcrum to the weight to be lifted is 2.0 m. If a…

A: The length of the lever is l = 5.0 m. The distance from the fulcrum to the weight to be lifted is x…

Q: A scaffold of mass 50 kg and length 4.8 m is supported in a horizontal position by a vertical cable…

A:

Q: Determine the net torque (about point P at one end) of the 4.0-m-long uniform beam shown in the…

A:

Q: At the local playground, a 21-kg child sits on the right end ofa horizontal teeter-totter, 1.8 m…

A:

Q: A horizontal, 16.5-m plank weighs 304 N. It rests on two supports that are placed 2.50 m from each…

A: Given L=plank length=16.5m Weight of plank=304 N Distance from and to supports=2.5m Weight of…

Q: If you are trying to balance a seesaw and you have a higher mass on the left, should the mass on the…

A: Introduction: Seesaw is a children swing found in children parks where two child sit on one-one ends…

Q: A force 107 N is applied to a rigid body. If the moment arm with respect to a given point O is = 5…

A:

Q: The fulcrum of a seesaw 4 m long is located 2.5 m from one end. A person weighing 300 N sits on the…

A: Given data: The length of seesaw is L=4 m. The fulcrum from one end is x=2.5 m. The weight of…

Q: Where must a 500 N weight be hung on a uniform 150 N pole with a length of 5 m so that a girl at one…

A: The diagram is given below that shows the above situation. The force applied by the girl is given…

Q: Determine the net torque (about point P at one end) of the 4.0-m-long uniform beam shown in the…

A:

Q: A light rod is being used as a lever as shown. The fulcrum is 1.20 m from the load and 2.40 m from…

A: Given: The mass of the load is 16.9 kg. The free-body diagram is given below.

Q: Determine the distance, y, down from the top of the pole shown in Figure 3.4, at which the resultant…

A:

Q: when one boy is sitting 1.2 m from the center of a see-saw, another boy must sit on the other side…

A:

Q: A scaffold of mass 47 kg and length 5.0 m is supported in a horizontal position by a vertical cable…

A: Given:- A  mass m1 = 47 kg   length L = 5.0 m is supported in a horizontal position by a vertical…

Q: 17 cm, Find the magnitude of the net torque on the wheel in Figure below about the axle through O,…

A:

Q: The plant in the picture has mass of 29 kg, and is hanging at a distance of 2.2 meters from the…

A: In this question we are given that the plant in the picture has mass of 29 kg, and is hanging at a…

Q: A 1 450-kg automobile has a wheel base (the distance between the axles) of 2.90 m. The automobile's…

A:

Q: A force of 5.0 N is applied at the end of a lever that has a length of 2.0 meters. If the force is…

A: Given value--- Force = 5 N. length = 2m. angle = 30 degree.  We have to find--- torque?

Q: To loosen the lid on a jar of jam 7.6 cm in diameter, a torque of11 N # m must be applied to the…

A: The applied torque to the circumference of the lid,   The extends of the wrench from the center of…

Q: The angle between the beam and the floor is 15.0 degrees. The angle between the rope and the…

A: Given Data : The mass of the beam is given as mbox = 9.60Kg. The mass of the beam is given as mb =…

Q: 500 N/m 1,000 N 300 N/m 900 Nm 4 m 2 m 1 m Prepare an FBD to determine the location (m with two…

A:

Q: If the torque required to loosen a nut on the wheel of a car has a magnitude of 41.8 N*m, what…

A:

Q: If the torque required to loosen a nut on the wheel of a car has a magnitude of 40.0 N•m, what force…

A:

Q: A rod 2.0 m long that has weights of 10 N and 30 N at its end. At what point should the rod  be…

A: F1d1=F2d2F1d1=F2L-d1 Let the 10 N weight is  on left end of rod and 30 N weight on the right end

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.