Suppose an alloy consists of a 75 wt% Sn-25 wt% Pb. i. List the phases present in the alloy at 185 °C. ii. Determine the composition of the phases present in (i). iii. Calculate the relative amount of each phase present at 183 °C in terms of the mass fraction. iv. Sketch with labels the microstructure of the alloy at the temperature of 183 °C – ΔΤ.

Suppose an alloy consists of a 75 wt% Sn-25 wt% Pb. i. List the phases present in the alloy at 185 °C. ii. Determine the composition of the phases present in (i). iii. Calculate the relative amount of each phase present at 183 °C in terms of the mass fraction. iv. Sketch with labels the microstructure of the alloy at the temperature of 183 °C – ΔΤ.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Describe the phases present at the eutectic temperature when the overall composition is x(Cu)= 0.5
Using the Ti-Cu phase diagram, if you start with 100 kg of a Ti-Cu mixture at 3000C and 10 wt. % Cu and cool down very slowly to point D (500 C), determine what phases are present at each letter, determine the compositions for each phase, and determine theweight in each phase. Point D): Phase(s) present Weight % of Cu in each phaseWeight of each phase
An alloy of Component A and Component B, which do not react but are miscible in all proportions in molten state, is used to manufacture “Fail Safe” devices for boiler. Narrate the effect of composition on equilibrium: Solid ↔ Liquid with the help of a phase diagram, if the melting point of A (900 ºC), B (350 ºC) and the lowest melting of all compositions is 280 ºC at 12.6% of A and 87.4% of B.
10.27 A hypothetical A-B alloy of composition 55 wt% B-45 wt% A at some temperature is found to consist of mass fractions of 0.5 for both a and 8 phases. If the composition of the B phase is 90 wt B-10 wt% A, what is the composition of the a phase?
Using the Mg-Pb phase diagram below, if you start at point A and cool down very slowly to room temperature (point D), sketch the microstructure associated with each letter, determine what phases are present at each letter, determine the compositions for each phase, and determine the weight in each phase. The Mg-Pb mixture has 20 wt. % Pb in it. You start with 100 kg.
(a) Sketch a Pressure-Temperature phase diagram for a pure substance X where liquid X is less dense than solid X. Insert an isobar at 1 atm and an isotherm at 300 K. Clearly label all physical states, triple point, critical temperature and any normal transition temperatures.
Given the H2O – NaCl phase diagram below, answer the three questions: Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. At a salt composition of 10%, what is the temperature at which ice will start melting? What is the eutectic temperature of the ice and salt formation?
A hypothetical A-B alloy of composition 54 wt% B-46 wt% A at some temperature is found to consist of mass fractions of 0.5 for both αand β phases. If the composition of the β phase is 89 wt% B-11 wt% A, what is the composition of the α phase? ________ wt% B
a-Arrange in a table the number of phases that can be observed at R.T in the range starting from zero to 6.67%C in an "Equilibrium Phase Diagram" and the corresponding three of the mechanical properties.b- Explain with examples the solid-solution, eutectic and peritectic observed phases.c- Draw the .microstructure of each phase
For an alloy containing 40% p Sn - 60% p Pb at a temperature of 150°C: (a) Which phases are gifts? (b) What is (are) the composition(s) of this (s) phase(s)? (c) Calculate as quantities relatives of each phase present in terms of the mass fraction. (image attached below)
Given a blank phase diagram, label the solid, liquid, and gas phases for a pure substance. Give the approximate temp. and pressure of the triple point, and determine what the substance's phase would be at a given temperature and pressure. Can you provide an example?
In a binary Fe-Fe3C system, what is the transformation that occurs when cooling an austenistic mixture of 2% C by weight from 1100°C to below the eutectoid temperature? What is the microstructure, and how is it formed? What are the concentrations of the total and partial phases? Data: eutectoid temperature: 723 ºC, eutectoid concentration: 0.76% C, limit concentration of ferrite: 0.022%, limit concentration of cementite: 6.7%.