System 1 System 2 (a) (b) 5. where H,(s) H2(s) = = %3D and (s+10) A- Consider now System 1, Fig 1 (a), with transfer function H, (s The input for the system is the unit-step function x(t) = 1. u(t) %3D a Find z(t) b. Give an estimation of its settling time. c. Give the value of the steady state value of z, z

System 1 System 2 (a) (b) 5. where H,(s) H2(s) = = %3D and (s+10) A- Consider now System 1, Fig 1 (a), with transfer function H, (s The input for the system is the unit-step function x(t) = 1. u(t) %3D a Find z(t) b. Give an estimation of its settling time. c. Give the value of the steady state value of z, z

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Impulse response of an LTI system is given by h(n)=δ(n+2)-2δ(n+1)+3δ(n)-2δ(n-1)+δ(n-2) = {1,-2,3,-2,1} Calculate the 5 point DFT H(k) of h(n). Now, Calculate the 8 point DFT of h(n). Generate h’(n), periodic version of h(n) by 5. Assume x’(n)={1,1,0,-1,-1}5. Calculate the periodic convolution of h’(n) and x’(n). Also calculate the circular convolution of h(n) and x(n)={1,1,0,-1,-1}.
Transfer function of the pulmonary system that represents alveolar pressure PA to Pao is given by H(s)=0.8∗8,5s2+4s+8,5H(s)=0.8∗8,5s2+4s+8,5 . for Pao = 5 mmH2O, PA at steady-state is …… mmH2O
Difference equation of a discrete-time causal (right-sided) LTI system, y(n) = 2 x(n) – x(n-1) -1/4 y(n-1) + 1/8 y(n-2) is given as. a) Give the system function H(z). b) Indicate zero, poles and ROC in the Z-plane. Is the system stable? Please explain. c) Find the impulse response of the system. d) If the system is left-sided, repeat (b) and (c).
A plant has the transfer function given by G(s)=1(s2+3s+1)(s2+7s+1)G(s)=1(s2+3s+1)(s2+7s+1) and is controlled by a proportional controller Gc(s)=KGc(s)=K as shown in the block diagram in Figure. For a stable system, calculate the value of KK that yields a steady-state error E(s)=Y(s)−R(s)E(s)=Y(s)−R(s) with a magnitude less than 0.010.01 for a unit step input.
The system function of a discrete-time causal LTI system is H(z) = z / (z2 +1.5 z -1) a) Show the poles/zeros and the ROC in the Z-plane. Is this system stable? Explain. b) Calculate the impulse response h(n). c) Give the difference equation of this system. d) Repeat questions (a), (b), (c) if this system is changed to be stable.
a linear time-invariant systems |z|>0.5 zone of convergence and transfer function H(z) which of the options (1,2,3,4) can be h(n)
From a compliance transfer function of a spring-mass–damper system, the stiffness is determined to have a value of 0.6 N/m, a natural frequency of 0.50 rad/s, and a damping coefficient of 0.089 kg/s.1. Neatly derive the expressions of the magnitude and phase of the mobility transfer function
Show that the derivative of a 1-D signal, I=I(x), amplifies the higher frequency components of the signal. Then, prove that even a slight amount of noise n=n(x), can be responsible for a large difference between the derivative I and I+n (Hint: Assume that n can be written as εsin(ωx) for some very small ε and very large ω).
4.Transfer function of the pulmonary system that represents alveolar pressure PAto Pao is given by ?(?)=0.8/?2+4?+1. How much is PAfor Pao = 5 mmH2O, at steady stateinmmH2O? The original of the problem is attached.
A DSP system is described by the following differential equation with zero initialcondition:y(n)+0.1y(n-1)-0.2y(n-2) =x(n)+x(n-1)a. Determine the impulse response y(n) due to the impulse sequence x(n) = (n).b. Determine system response y(n) due to the unit step function excitation, where u(n)= 1 for n  0.
I need help with the question below Consider a causal LTI continuous system described by the differential equation y′′(t) + 3y′(t) + 2y(t) = x(t) where y(t) is the system output and x(t) is the input.1. Find the transfer function H(s) of the system.2. Find its poles and zeros. From its poles and zeros, determine if the system is BIBO stable or not.3. If x(t) = u(t) and initial conditions are zero, determine the steady-state response yss(t)4. If the initial conditions were not zero, would you get the same steady state?. Explain
a linear time-invariant systems |z|>0.5 zone of convergence and transfer function H(z) is system causal ? (true/false)