Please I request u do this question according to your experience u can take help from internet I will give u 3 likes Table 3: Record the resistances, including uncertainty. You can report the uncertainty in the usual way (l.e., in the standard format), or you can justgive a range of values if the numbers were fluctuation. Ex: If the value for the resistance on the meter wos fluctuating from a low of about 200k2 upto a maximum of about 400k2, you could write that as 200ks2 - 400k2, or 300KS4 100Okn.Name of objectResistance, including uncertainty. Seecaption for details about uncertainty.between two handsbetween hands & under waterone wire (between two alligator clip ends)You in parallel with this lab's largest RYou in parallel with this lab's smallest R

Resistance: It is the value by which a object opposes the electric force or current. The higher the…

Table 3: Record the resistances, including uncertainty. You can report the uncertainty in the usual way (i.e., in the standard format), or you con just give a range of values if the numbers were fluctuation. Ex: If the value for the resistance on the meter was fluctuating from a low of about 200k2 up to a maximum of about 400k2 you could write that as 200k2 - 400K2, or 300KSH 100ka Name of object Resistance, including uncertainty. See caption for details about uncertainty. between two hands between hands & under water one wire (between two alligator clip ends) You in parallel with this lab's largest R You in parallel with this lab's smallest R

Table 3: Record the resistances, including uncertainty. You can report the uncertainty in the usual way (i.e., in the standard format), or you con just give a range of values if the numbers were fluctuation. Ex: If the value for the resistance on the meter was fluctuating from a low of about 200k2 up to a maximum of about 400k2 you could write that as 200k2 - 400K2, or 300KSH 100ka Name of object Resistance, including uncertainty. See caption for details about uncertainty. between two hands between hands & under water one wire (between two alligator clip ends) You in parallel with this lab's largest R You in parallel with this lab's smallest R

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 22RQ

See similar textbooks

Similar questions

Since R1=5619.38ohm, R2=1949.32ohm and Ri=Infinite in the circuit given in the figure, write the equivalent resistance in Ohms between the terminals A-B. When making your transactions, 2 digits will be taken after the dot.
Look at the images shown. Why can we measure resistance with a pencil drawn on a piece of paper? What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance? 0.449 mega ohms 102.2 kilo ohms
Suppose we include the lead resistance in the calculation of temperature for a class A RTD. If R3 = 1000 ohms, Ra = 18 ohms, V0 = 1.80 volts, and V = 5 volts. Including the tolerances, what is the highest temperature you could measure in °C? (Type in a two-decimal number)
A typical exterior masonry wall of a house, shownin the accompanying figure, consists of the items in theaccompanying table. Assume an inside room temperature of 68F and an outside air temperature of 10F,with an exposed area of 150 ft2. Calculate the heat lossthrough the wall.
Complete the sentence! Connection by the method indicated in the figure is preferable for the measurements of the resistances - …… medium and large over 10 000 ohms small below 100 ohms very large over 1000 G ohms
1. What is the minimum tolerance? a. 386K b. 387K c. 388K 2. What is the maximum tolerance? a. 470K b. 473K c. 475K
Determine the resistance of a bus bar made of aluminum at 50°C if the length is 15 meters long and cross section is 9cm2 Note: DRAW THE DIAGRAM
Answer must be in standard form scientific notation with SI units that do not have prefixes except for kg. Provide the answer with the correct amount of significant figures. Thank you so much I greatly appreciate it. Note: all information is provided, the emf values of E1 and E2 are unknown, however we are not looking to find the EMF values. We are looking to find the resistance R
A resistor with color bonds blue-red-green-yellow-gold has a length of 5cm. If the material is made out of carbon, how much material (in terms of volume) is present in this resistor? If you are going to change the carbon to glass, how much smaller would it be? (Note take the lower limit of the final resistance and the resistivity constant of carbon and glass) Follow the format: Given: Required: Equation: Solution: Answer:
When electricity is transported from a power station to a city, the line voltage (relative to ground) is usually on the order of several hundred thousand volts. A power line cable has a radius of a = 2.0 cm, is made of aluminum with a resistivity of ρ = 2.7×10−8 Ω ⋅ m, and spans a distance of l = 100 km from a power station to a city. The city consumes 100 MW of power (so I2RL =100MW). (a) Find the resistance of the power cable between the station and the city(i.e.,between points A and B). (b) Suppose that the line voltage ∆VBC = 120 V. i. How much current is required to flow through the power line to deliver 100MW of power to the city? ii. How much energy is lost as heat between points A and B? (c) Suppose that the line voltage ∆VBC = 300 kV. i. How much current is required to flow through the power line to deliver 100MW of power to the city? ii. How much energy is lost as heat between points A and B?
The resistance of a certain aluminum power line is 150 Ω at 200 Find the line resistance when the sun heats up the line to 420C. First, use the inferred zero resistance temperature formula and then the temperature coefficient of resistance formula to show that the two formulas are equivalent.
Q2: Does ‘a three digit color coding of resistor values’ limit producible resistor value ranges? Why? If you need to increase these range what would be your solution? please write a detailed answer ,,, tahnk you