TABLE 5.10 Maximum Spans for Floor Joists (ft-in.)a Joist Size Spacing (in.) 2 x6 2 x 8 2x 10 2 x 12 Live load = 40 psf, Dead load = 10 psf, Maximum live-load deflection = L/360 12 10-9 14-2 17-9 20-7 16 9-9 12-7 15-5 17-10 19.2 9-1 11-6 10-3 14-1 16-3 24 8-1 12-7 14-7 Live load = 40 psf, Dead load = 20 psf, Maximum live-load deflection = L/360 12 10-6 13-3 16-3 18-10 16 9-1 11-6 14-1 16-3 19.2 8-3 10-6 12-10 14-10 24 7-5 9-50 11-6 13-4

TABLE 5.10 Maximum Spans for Floor Joists (ft-in.)a Joist Size Spacing (in.) 2 x6 2 x 8 2x 10 2 x 12 Live load = 40 psf, Dead load = 10 psf, Maximum live-load deflection = L/360 12 10-9 14-2 17-9 20-7 16 9-9 12-7 15-5 17-10 19.2 9-1 11-6 10-3 14-1 16-3 24 8-1 12-7 14-7 Live load = 40 psf, Dead load = 20 psf, Maximum live-load deflection = L/360 12 10-6 13-3 16-3 18-10 16 9-1 11-6 14-1 16-3 19.2 8-3 10-6 12-10 14-10 24 7-5 9-50 11-6 13-4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported rectangular beam 9 in. wide having an effective depth of 12 in. carries a total factored load of 16.201 kips/ft on a 40 ft clear span. It is reinforced with 10.92 in² of tensile steel, which continues uninterrupted into the supports. If f'c= 3000 psi, fyt= 40,000 psithroughout what part of the beam is web reinforcement required?. Using vertical U stirrups with fyt= 40, 000 psi, design the web reinforcement for the beam,the stirrup spacing and total spacing for the beam.
a. What is the value of the distributed load in beam B2 in plf (lb/ft)? b. What is the value of each of the point loads acting on girder G1 in kips to one decimal place? c. What is the value of the force in column C6 in the ground floor (in kips to one decimal place)?
A simply supported rectangular beam 14 in. wide having an effective depth of 15.5 in. carries a total factored load of 10.382 kips/ft on a 25 ft clear span. It is reinforced with 3.81 in² of tensile steel, which continues uninterrupted into the supports. If f'c = 3000 psi and fyt = 40000 psi throughout what part of the beam is web reinforcement required?. Using vertical U stirrups with fyt = 40.000 psi, design the web reinforcement for the beam and the stirrup spacing and total spacing for the beam
Determine the ultimate uniform load, wu of EACH beam indicated in the typical floor plan shown below. Assume all beams are carrying CHB wall except B5. Heigth of the wall is 3.25 m. Use load combination wu = 1.2DL + 1.6LL all beams. Assume the following design criteria: Concrete Slab = 23.6 KN/m3 Floor Finish = 0.05 KPa Slab Thickness: S1 = 0.125 m, S2 = 0.15 m Typical Interior Beam Sections = 200 mm x 400 mm Typical Exterior Beam Sections = 200 mm x 350 mm Ceiling System = 0.50 KPa 4” CHB both faces plastered (For Interior Walls) = 2.10 KPa 6” CHB both faces plastered (For Exterior Walls) = 2.73 KPa Residential Basic Floor Area Summarize all your load ouputs using table.
What is the maximum span for a 7.5-inch thick post-tensioned concrete two-way flat plate? Answer from: 6ft, 22ft, 25ft, 28ft
a. What is the value of the distributed load in beam B1 in plf (lb/ft)?b. What is the value of each of the point loads acting on girder G2 in kips to one decimal place?c. What is the value of the force in column C1 in the ground floor (in kips to one decimal place)?
Refer to the elevation plan and schedule of beam shown. Use girder 2B1 to layout the rebar. Compute and estimate: a. Create a rebar cutting list for stirrups needed for the three spans shown using 2B1. Consider the restrictions in tension zones.
Q1- the reinforced flat plate roof slab system that shownin figure. Supports a service live load of 1.5 kN / m2 and a service superimposed dead load of 3.4 kN / m? in addition to its own weight. The slab is supported along its outer edges by a brick wall. Slab thickness is 200mm and wall thickness is 240mm. all interior columns are 300x600 mm. Using the ACI direct design method, design and detail the column strip top bars required at the continuous edges of strip A shown in the plan. Use fe-22 MPa andf-400MP.
Design the most economical W-shape for a typical filler beam and interior girder in the partial framing plan.For both structural members, draw load diagrams and solve for reactions. thank you for the help
Figure B1 shows a simply supported beam is of symmetrical I section with flange 90 x10 and web70 x 10 with a span of 7m carrying u.d.l of 8KN/m over entire span and acentral point load of 20KN.Rajah B1 menunjukan sebuah rasuk tertupang mudah yang merupakan keratan rasuksimetri seksyen I dengan dimensi bebibir 90 x 10 dan web 70 x 10 dengan rentang rasuksepanjang 7m yang membawa beban teragih seragam 8KN/m sepanjang rasuk dandibebankan dengan beban tumpu 20KN di tengah rentang. 20KN 8 KN/m A B 3.5m 3.5mFigure B1/ Rajah B1 (i) Analyze the reactions at the support and illustrate the shear force diagram andbending moment diagram.Lakukan Analisa daya tindakbalas dan ilustrasikan gambarajah daya ricihdan momen lentur.
Draw the details of the most efficient beam in terms of flexure if the beam is cast in place, non-prestressed and exposed to weather or in contact with the ground. Beam section: 300mm x 450mm rectangular beam reinforced with 12mm diameter stirrups and 6pcs - 32 mm diameter longitudinal top bars.
A rectangular beam has b = 300 mm, d = 500 mm, As = 6 – 32 mm, f’c = 27.6 MPa, grade 60 reinforcement (fy = 414 MPa). Calculate the ultimate moment capacity of the beam.