A 54 kg crate with c.g. G2 rests on the 27 kg pickup tailgate with c.g. G1. Determine the tension in the two restraining cables, one of which is shown (AB), and the x; y components of the reactions at the two supports O. Note: there are two restraining cables and two pivot points O. The crate is located midway between the two support cables (i.e. into the page). Record your numerical answers in the table below (indicating directions). 350 mm B 300 G mm G1 240 mm 70 mm

A 54 kg crate with c.g. G2 rests on the 27 kg pickup tailgate with c.g. G1. Determine the tension in the two restraining cables, one of which is shown (AB), and the x; y components of the reactions at the two supports O. Note: there are two restraining cables and two pivot points O. The crate is located midway between the two support cables (i.e. into the page). Record your numerical answers in the table below (indicating directions). 350 mm B 300 G mm G1 240 mm 70 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7.3 The jib crane supports a load of F = 710 lb from the trolley which rides on the top of the jib. Determine the internal normal force, shear force, and moment in the jib at point C when the trolley is at the position shown. The crane members are pinned together at B, E and F and supported by a short link BH. Determine the internal normal force at point C. Determine the shear force at point C.
Statics Review. Make sure to draw FBD(s). Given the beam with loading as shown below: A 2 kN/m ILITI PE 5m B f 5m Find: (a) The reactions at A and D (b) The internal shear force at C (c) The internal moment at C 20kN E 5m с + 5m D UMI
A boom AB is supported in a horizontal position by a hinge at A and a cable which turns from C, over a small pulley at D. Compute the tension T in the cable and the horizontal and vertical components of the reaction at A. Neglect the size of the pulley at D.
Determine the reactions of the pin support at point A and thetension cables if F = 375lbs.
(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures. (b) Redo problem (a) by using the bending moments over support A and B as the redundant forces. (c) Repeat problem (a) if there are support settlements of 8mm, 5mm and 2mm at A, B and C respectively. Given E=200GPa, I=107mm4 .
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
In the cantilever shown, taking M1 = 16 kN-m, M2 = 11 kN-m, P1 = 3 kN, P2 = 7 kN.a) Determine the vertical reaction at "A"
Determine the tension in the cables and also the force P required tosupport the 600-N force using the frictionless pulley system shown.
Give me the solutions of this. Identity the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m
The steel framework is used to support the 4-in. reinforced stone concrete slab that carries a uniform live loading of 400 lb/ft2. Sketch the loading that acts along members BE and FED. Set a = 9 ft, b = 12 ft. Hint: See Table 1.2.
The wall crane supports a load of 700 Determine the horizontal and vertical components of reaction at the pins at A and D. Also, what is the force in the cable at the winch W?
The wall crane supports a load of 700lb. Determine the horizontal and vertical components of reaction at the pins A and D. Also, what is the force in the cable at the winch W? The jib ABC has a weight of 100 lb and member BD has a weight of 40 lb. Each member is uniform and has a center of gravity at its center.