Task III (Equilibrium of Rigid Body) If the beam in the figure below is in equilibrium (A is a pin and B is a roller), determine the following: (Neglect the thickness of the beam) 450 N 300 N 30% B -4 m D. Write the equilibrium equation of the moment around point A. E. Determine the reaction forces acts on A and B.

Task III (Equilibrium of Rigid Body) If the beam in the figure below is in equilibrium (A is a pin and B is a roller), determine the following: (Neglect the thickness of the beam) 450 N 300 N 30% B -4 m D. Write the equilibrium equation of the moment around point A. E. Determine the reaction forces acts on A and B.

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section8.2: Rotational Dynamics

Problem 24PP

See similar textbooks

Similar questions

hi, can you pls explain this to me? our topic is Torque or moment of a force. Thank you a) Describe translational equilibrium and the conditions for this stage b) define the center of gravity
A thin, light string is wrapped around the rim of a 3.75-kgkg, solid, uniform disk (similar to a puck on ice without friction) that is 33.0 cmcm in diameter. A person pulls on the string with a constant force of 98.00 NN tangent to the disk, as shown in the figure below (Figure 1). The disk is not attached to anything and is free to move and turn. Part A Find the angular acceleration of the disk about its center of mass. Express your answer in radians per second squared. Part B Find the linear acceleration of its center of mass. Express your answer in meters per second squared. Part C If the disk is replaced by a hollow, thin-walled cylinder of the same mass and diameter, what will be the angular acceleration of the disk about its center of mass? Express your answer in radians per second squared. Part D If the disk is replaced by a hollow, thin-walled cylinder of the same mass and diameter, what will be the linear acceleration of its center of mass? Express your…
Three forces are applied to a wheel of radius 0.350 mm, as shown in the figure (Figure 1). One force is perpendicular to the rim, one is tangent to it, and the other one makes a 40.0∘∘ angle with the radius. a) What is the magnitude of the net torque on the wheel due to these three forces for an axis perpendicular to the wheel and passing through its center? Express your answer in newton-meters. b) What is the direction of the net torque in part (A)? What is the direction of the net torque in part (A)? into the page out of the page
Compute the torques produced by the following forces. Be sure to indicate whether the torque action is CW or CCW.
Sierra holds a box in her hand using her elbow flexor muscles (see picture). Her forearm is at a 35° angle relative to the horizontal. c.) If the moment arm (dm) of the elbow flexor muscle force (Fm) is 0.032m, how much force must the muscles generate get a muscle torque sufficient to balance the torque of the box?
You are using a wrench to rotate a bolt around its center. Consider all the forces in the figure below, indicated by the arrows, to have the same magnitude. Rank the scenarios in terms of the magnitude of the torque applied, from smallest to largest torque.
ASSIGNMENT No. 12: Moments of Inertia Solve for the moment of inertia of areas and solids of revolution. Solve and draw the following: Find the moment of inertia with respect to the axis of revolution of a circular cone.
The rope shown in Figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, (a)what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation.(b) What happens if the frictional force between table and cylinder is negligible? Choose any axis tor yourcomputation.
The answers are provided; please explain the purpose of each equation and why they were used Consider a bar of length 5.5 m, being acted on by three forces and constrained to rotate about its left end. The magnitudes of the first two forces are 19 N and 28 N and the first force is acting on the end of the bar at an angle of 43° What is the torque in newton-meters, due to F1 on this bar relative to the left end? Ans. = 78.87 Nm Equation used: τ1 = rFsinθ What is the torque in newton-meters, due to F2 on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. Ans. = 77 Nm Equation used: τ2 = F2 x (L / 2) What is the magnitude of the force F3, in newtons, if the force is a distance 0.85 m from the left end and the bar is not rotating? Ans. = 183.38 N Equation used: F = (τ1 + τ2) / d
PLEASE SEND THE ANSWER IN 10 MINUTES !!! Consider the system shown below. Two masses are attached to each other by a massless string passing through a pulley. It is given that m2<m1 and the pulley has a moment of inertia of I. The system is released from rest at the instant shown below and the string does not slip on the pulley. Is the following statement true or false? As the system moves, the angular speed of the pulley is equal to the speed of the block divided by the radius of the pulley, ?=?/?
PLEASE SEND THE ANSWER IN 10 MINUTES !!! Consider the system shown below. Two masses are attached to each other by a massless string passing through a pulley. It is given that m2<m1 and the pulley has a moment of inertia of I. The system is released from rest at the instant shown below and the string does not slip on the pulley. Is the following statement true or false? As the system moves, the angular speed of the pulley is equal to the speed of the block divided by the radius of the pulley, w=v/R
A solid wheel shown in the diagram, has a mass of 3 kg and a diameter of 0.55 m. It starts to rotate from rest to 10 revis in 35 seconds a) What torque is needed to apply to the wheel? b) If a strap is wrapped around the outside of the wheel, how much force do you need to exert on the strap? Please show your work step by step.