Water at 21.76 psi and 24°C enters the boiler through a 3 in. Sch. 40 pipe at a rate of 264.40 gpm. It exits at a height of 25 m above the inlet at 150°C and21.76 psi at a rate of 260.275 gpm through a 1.5 in. Sch. 40 pipe. Assuming the process to be steady state and the flow to be turbulent, calculate heatrequired to be added per kg of steam.

Answered: Image /qna-images/answer/5a51898b-c8da-405d-ad45-bd8a49ce9652.jpg

ter at 21.76 psi and 24°C enters the boiler through a 3 in. Sch. 40 pipe at a rate of 264.40 gpm. It exits at a height of 25 m above the inlet at 15 76 psi at a rate of 260.275 gpm through a 1.5 in. Sch. 40 pipe. Assuming the process to be steady state and the flow to be turbulent, calculate uired to be added ner ka of steam

ter at 21.76 psi and 24°C enters the boiler through a 3 in. Sch. 40 pipe at a rate of 264.40 gpm. It exits at a height of 25 m above the inlet at 15 76 psi at a rate of 260.275 gpm through a 1.5 in. Sch. 40 pipe. Assuming the process to be steady state and the flow to be turbulent, calculate uired to be added ner ka of steam

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flashed steam geothermal power plant is located where underground hot water is available as a saturated liquid at 700 kPa. The well-head pressure is 600 kPa. The flashed steam enters the steam turbine at 500 kPa and expands to 15 kPa when it is condensed. The flow rate from the well is 29.6 kg/s. Determine the cycle thermal efficiency of the plant in %. FINAL ANSWER MUST BE IN 3 DECIMAL POINTS
A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating capacity. Which of the following pipe size and velocity in feet per second (fps) for the main would be needed if the plant is a 62 psig medium-pressure steam system? (Hint: Table 7.2) a.8" pipe at 130 fps b.4" pipe at 150 fps c.2" pipe at 100 fps d.4" pipe at 130 fps e.5506 MBH; 62 psig
Answer this ASAP,thx In a steam turbine, saturated steam enters the turbine at a pressure of 16 MPa and a pressure in the condenser of 8 kPa. The mass flow rate of the fluid entering the turbine is 100 kg/s. calculate: A) the power produced B) the rate of heat transferred to the steam passing through the boiler C) the thermal efficiency
i . A gas well is flowing at a flow rate of 1.2x105scf/d with the surface pressure of 500psi and compressor inlet pressure of 100psi. Calculate the horse power requirement.
A plant located at an altitude of 925 m has an open feedwater heater located 2.76 m above the pump intake. The water in the heater has a temperature of 65ºC. If the head loss in the suction line is 0.8 m. Determine: a. Atmospheric pressure head, in meter b. Vapor/saturation pressure head, in meter c. The Net Positive Suction Head.
The refrigerant fluid(Freon 12 or R12) flowing through the pipe with a pressure of 1 MPa and a temperature of 80oC is cooled to 1MPa pressure and 30oC with the air passed through the pipes in a condenser. The air at a flow rate of 800 m3/min enters the condenser at 100 kPa pressure and 27oC temperature and exits at 95 kPa pressure and 60oC temperature. Calculate the mass flow of refrigerant.
5. A single-acting, twin-cylinder 15.25 x 15.25-cm compressor receives saturated ammonia vapor at - 18 degrees * C and discharges it at 1514.3 kPa. The system is used to produce ice at a final temperature of - 10 degrees * C from water at 27 degrees * C . The compressor runs at 450 rpm with an actual volumetric efficiency of 78%. Assume compression and mechanical efficiencies to be 82% and 88%, respectively. Calculate the following: (a) capacity of the system in tons of refrigeration, (b) brake hp required by the compressor, (c) tons of ice produced per day if compressor runs only 20 hours a day. Assume losses to be 10% of the refrigeration required to produce the ice, and (d) ideal and actual COP.
a 140x140-mm, twin-cylinder, single acting refrigerant-12 compressor running at 600 rpm carries a refrigeration capacity of 40kW while operating at 350 kPa suction and 1300 kPa discharge pressures, assuming the same load to be carried with the same volumetric efficiency and if the discharge pressure shall be raised to 1400 kPa, a) what is the percent increase in mass of R-12 b.) what will be the new volumetric displacement of the compressor in m3/sec c.) at what speed should the compressor be run?
A trial run on a steam turbine power plant gave the following resultsEntrance to boiler Exit of turbineMass flow rate =3600 kg/h Velocity of steam=25 m/sEnthalpy of water=850 kJ/kg Elevation above datum=0Elevation above datum=4.3 m Enthalpy of steam=2625 kJ/kgVelocity of water=5 m/sDetermine the power developed by the turbine if the heat added in the boiler is 2100 kJ/s.
Siemens manufactures industrial steam turbines for use in various fields of application. One of the turbines offered in its catalog is the SST-400, designed for power generation. Its technical data are: - 60 MW delivered power with a flow rate of 60 kg/s. - Inlet pressure 12.5 MPa - Outlet conditions: wet steam at 30 kPa, with a quality of 0.90. Determine the temperature at which the steam enters the turbine. State explicitly, the assumptions you have made to solve the problem.
In an ammonia refrigerator , the pressure in the evaporator is 267. 58 KPa and the ammonia at is 0.14 dry while at the exit is 0.86 dry . During compression the work done per kg of ammonia is 20 ,000 kg .m . Calculate volume of the vapor entering the compressor per minute if the rate of ammonia circulation is 6.54 kg. The compressor has a volumetric efficiency of 90% and it runs at 150 rpm .The ratio of stroke to bore is 1 .Latent enthalpy of ammonia at based on its evaporating pressure is 320 Kcal per kg and its latent specific volume of ammonia based on its evaporating pressure is 0.436 m3 per kg .Specific volume of ammonia WITH PH DIAGRAM
A refrigerant 22 refrigeration carries a load of 82 kW at an evaporator pressure of 354 kPa and a condenser pressure of 1460 kPa. The liquid refrigerant is subcooled by 4 degrees before entering the expansion valve and the vapor is superheated by 5 degrees before entering the compressor. The stroke-to-bore ratio of the twin-cylinder compressor is 1.20 and the actual volumetric efficiency is 81 percent. Determine: a. The mass flowrate of the cooling water in the condenser for a 7-degree change in temperature, b. The bore and stroke