The 10-kg slender bar has a length of L = 5 m and released from rest in the horizontal position 1 and falls to position 2. What is the velocity of the mass center of the bar when it is in position 2?. G 2 Lütfen birini seçin: a. None O b. 6.71 m/s c. 9.59 m/s d. 3.88 m/s O e. 0.96 m/s

The 10-kg slender bar has a length of L = 5 m and released from rest in the horizontal position 1 and falls to position 2. What is the velocity of the mass center of the bar when it is in position 2?. G 2 Lütfen birini seçin: a. None O b. 6.71 m/s c. 9.59 m/s d. 3.88 m/s O e. 0.96 m/s

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Related questions

Q: The moment of inertia of the pulley about its axis is I = 0.005 kg.m?. If the 5-kg mass A is…

Q: Question 17 The 3-kg disk Dis attached to the end of a cord. The other end is attached to ball and…

A: We have given

Q: In Figure 6(b), the rotating elements B, which weigh 1288 lb and have a radius gyration of k =…

A: Given: The weight of B, M = 1288 lb The weight of A, m = 2.78 lb The radius of gyration, k = 2.5 ft…

Q: 4 Two chulciren, A and B, each having a masa of 30 kg sit at dhe edge of the merry go-round which is…

Q: The 30-kg uniform thin hollow square plate is pinned at point 0, and its side L = 0.2 m. If it is…

Q: A solid cylinder starts up the 30° inclined plane with a mass center speed of 8 m/s. If it rolls…

Q: Time left 0:24 Two boxes of masses m, =2.5 kg and m2 =7.5 kg are connected over a disk shaped pulley…

Q: The T-shaped body of total mass m = 6.5 kg is constructed of uniform rod. If it is released from…

Q: HW 8. During an engine test on the ground, a propeller thrust T =3000 N is generated on the 1800-kg…

Q: The 25-lb slender rod has a length of 6 ft. Using a collar of negligble mass, its end A is confined…

Q: velocity of 34 rad.s1. Disk E has a weight of 65 lb : is initially at rest when it is brought into…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: The crank OA rotates in the vertical plane with a constant clockwise angular velocity wo of 2.0…

A: Consider the clockwise sense of rotation as positive and write the expression for magnitude of…

Q: Q12. The two tugboats each exert a constant force F = 20 N on the ship as shown in Figure Q12 These…

Q: The grooved pulley of mass m is acted on by a con- stant force F through a cable which is wrapped…

Q: 100 mm 175 mm The uniform disk has mass 25 kg sits at rest on fixed ground, at this insta nt, a…

A: Given, Force, F=80Nstatic friction,μs=0.20kinetic friction,μk=0.12mass of disk, m=25kgradius of the…

Q: Q5) A rod having a mass of M and length of L is falling. What is the equation of motion if the…

A: The free body diagram of the rod is given below,

Q: 0.61 slug Acceleration of C = 15.7ft/s² Mass of plate %3D Determine angle & at T. 0.4' this instat.…

Q: A m=0.25kg mass is attached to end of a thin uniform rod of mass M =1.34kg and length L=3.33m which…

A: The above question is based on conservation of Energy.

Q: is pin supported at its center. The 30-kg disk shown in: Determine the angle through which it must…

Q: Given: (M & K ??Ed ??) The system shown is released from rest. The weight of block A is WA 30 lbf…

A: Given: The system is shown below: Weight of A is 30 lbf. Weight of B is 5 lbf.

Q: The shown rod AB has its motion constrained such that its ends move along the illustrated grooved…

Q: force P that is parallel to the incline. The mass of the mower with attached grass bag is 50 kg with…

A: Draw the free body diagram Apply the condition of equilibium ,ΣFx=0 , P-wsinθ=0 w=mg…

Q: In the mechanism below, neglect the inertias of all the links and determine the cable tension force…

Q: Bbch A hes a mass of 7kp. 5tatic ond khe tic fricton coe ffieients of the inclined surface ore 0.4…

A: Given data as per question Mass =7kg Static coefficient of friction =0.4 Kinetic coefficient of…

Q: The 13.5-kg rod is released from rest when 0=tan-(3/4) [position 1]. Knowing that AB=1.8 m. The…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: The car has a mass of 1234 kg and a center of mass G. Determine the acceleration if the rear…

A: Frictional force is defined as the force of resistance offered by the surface which opposes the…

Q: stude techanisms class ted a doohickey consisting of a bar with uniform thickness and width, total…

Q: Figure Q10 shows an illustration of a ballistic pendulum that is used for determining A is M = 10…

A: GivenL=1.0mM=10kgm=38gθ=26° The collision is completely inelastic

Q: The crank OA rotates in the vertical plane with a constant clockwise angular velocity wo of 4.8…

Q: 1. Determine the maximum weight of body B in the figure that will permit the homogenous 50lb block A…

Q: The door has a mass of m and a center of gravity at G. The door is pushed on with a force F at…

Q: 13. in the figure shown to thie right, in the ab- sence of gravity the springs are unstretched iu…

Q: Two blocks are free to slide along the frictionless wooden track shown below. The block of mass m, -…

A: AS PER COMPANY POLICY, ONLY ONE QUESTION CAN BE SOLVED AT A TIME. FOR SOLUTION OF OTHER QUESTIONS,…

Q: A string is wrapped around the inner hub of a 'yo-yo' and is fixed at A. The yo-yo has a mass of 4…

A: Given data: The mass of yo-yo, m = 4 kg. The moment of inertia of yo-yo, I = 0.06 kg·m2. The height…

Q: Disk "A" of weight 5 lb and radius "r=3 in" is at rest and placed in contact with a belt which moves…

Q: The disk has a radius of 3.00 cm and a mass of 30.0 grams and is initially at rest. Starting at time…

Q: A physics student of mass 43.0 kg is standing at the edge of theflat roof of a building, 12.0 m…

A: Given data:

Q: 2000-lb bike with a rear wheel drive has a wheelbase of 10 ft. The c.g. is 3 ft above the pavement…

Q: Each arm of aporter govern or is 250 mm long The uppe r and ower arms are pivoted at 40mm and 50 mm…

A: Introduction: When the load on an engine is reduced, the engine's speed suddenly increases the…

Q: A load of W (kN) with corners ABCD standing still in the truck bed wants to be transported.Since it…

A: Given data: Load, W=6kN b=0.3m d=0.9m e=1.7m Condition: the load does not slide during the…

Q: The mass center, G, of the 2-lb ball has a velocity of Ivch - 5 tis when it strikes the end of the…

A: Here we have mass of ball =2lb(pound)initial velocity of ball=5ft/slength of bar =5ftHeight of bar…

Q: 2m m. di, d₂ and ₂ are the joint variables None of them m₂ = m₁ = m₂ = M₁₂ = 1 kg The moment of…

Q: motion of the block of mass ( m.) for 2 -Determine the magnitude ( P) of the horizontal force…

Q: In the mechanism below, neglect the inertias of all the links and determine the cable tension force…

A: given data; →mass (M)=1.424kg→FC=CD=0.8→FD=FC+CD =0.8+0.8 =1.6m→tension in cable=T→lets…

Q: (b) The 0.31 Kg mass slides at the shown frictionless wire that lies in a vertical plane. What is…

Q: In Figure 6(b), the rotating elements B, which weigh 1288 lb and have a radius gyration of k =…

A: Given: The weight of B, W = 1288 lb The weight of A, w = 2.78 lb The radius of gyration, k = 2.5 ft…

Q: Mechanical Engine Give step by step solutic The uniform rod AB of mass 10 kg can rotate about an…

A: givenmass of uniform rod m1=10kglength of uniform rod L=0.36mtriangluar wodden mass m2=50kgheight of…

Q: The handcart has a mass of 215 kg and center of mass at G. A force P=1075 N that is applied to the…

Question

The 10-kg slender bar has a length of L = 5 m and released from rest in the horizontal position 1 and falls to position 2. What is the velocity of the mass center
of the bar when it is in position 2?.
L
G
Lütfen birini seçin:
a. None
O b. 6.71 m/s
O c. 9.59 m/s
O d. 3.88 m/s
O e. 0.96 m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Just like the change in momentum over time generates a force (P=F) , the change in ∆t angular moment results in a torque (L = τ) . Using the theoretical values for the moments∆tof inertia of the hollow cylinder and disk, determine the torque done on the system whenthe cylinder is dropped on the disk. Take ωi = 9.5 rd/s, ωf = 6.1 rd/s, and ∆ t = 2 s
AB bar, negligible weightmovement on the surface indicated by the wheelsis doing. The bar is at rest when θ = 0°is being released. A and B when θ = 30°Find the velocities of the points.
The velocity of the 8-kg cylinder is 0.3 m∕s at a certain instant. The speed v after dropping an additional 1.5 m is 2.5 m/s. The mass of the grooved drum is 12 kg, its centroidal radius of gyration is k = 210 mm, and the radius of its groove is ri = 200 mm. The frictional moment at O is a constant 3 N∙m. Find the frictional force.
The T-shaped body of total mass m = 6.5 kg is constructed of uniform rod. If it is released from rest while in the position shown, determine the vertical force reaction at O as it passes the vertical position (124° after release). The distance b is 1.04 m.
A hammer head H having a weight of 0.26 lb is moving downwards at 40 ft/s when it strikes the head of a nail of negligible mass and drives it into a block of wood as shown. Find the impulse on the nail if it is assumed that the grip at A is loose, the handle has a negligible mass, and the hammer stays in contact with the nail while it comes to rest. [Show work fast , Don't copy]
The homogeneous sphere with mass m is held 1 m above the horizontal plane and rotates with an angular velocity of 30 rad/s clockwise. The sphere is then released and falls impacting the ground below at A. Determine the velocity of the centre of mass of the sphere after it bounces. Assume the ground is rough so no slipping occurs, and the coefficient of restitution is 0.9. Solve all questions using Impulse and Momentum methods
Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
A 256-lb block is released from rest when the spring is unstretched. The drum has a weight of 76 lb and a radius of gyration of kO = 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k=78 lb/ft. The radius of the drum are: rin=0.485ft and rout=0.82ft. Find the velocity of the block after it has descended d=4 feet.
The homogeneous cylinder A has a mass of 80 kg, and the mss of the hub can be neglected. The magnitude of the variable force P, is in newtons when t is in sec- onds. The velocity of body B changes from 2 m/s downward when t = 0 to 4 m/s downward t = 5 s. Determine the mass of B. Solve all questions using Impulse and Momentum methods
A load of W (kN) with corners ABCD standing still in the truck bed wants to be transported.Since it is known that the load does not slide during the movement, the maximum acceleration that the truck can reach without tipping the load and Calculate the coefficient of friction between the load and the truck bed. (C represents the center of gravity of the load). W=6kN b=0.3m d=0.9m e=1.7m
A brake mechanism is used to lower body A with a constant velocity of 3.0 m/s. The coefficient of friction between the brake and drum D is 0.40. Neglect the weight of the brake. Determine the mass of body A and the power dissipated by the brake. (hint: the normal force between the brake the and disk is not 1200 N)
Q1: A cylindrical body has a mass Mand outer radius R (the moment of inertia I I= 1 2 MR^ 2 ) starts to roll from rest (upper position) down on an inclined surface. If the effect of friction force was ignored, determine the linear speed of the cylinder when it hits level ground a height h lower.