The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjectedto an external load of 15 kN as shown. Calculate the maximum circumferential and longitudinal stresses(in MPa) experienced by the tank. The thickness of the tank is 30 mm.175 cm60cm115 KNØ'15 KN

Givenh=2mP=2MPaFex=15kNt=30mm=0.030m

Answered: The 2-meter-high pressure tank below…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 4-ft diameter spherical tank is subjected to an internal pressure of 10 psf. If the wall thickness is 0.70", determine the tangential stress of the wall in psi.
The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the endcap.
When filled to capacity, the unpressurized storage tank shown in Figure contains water to a height of h = 30 ft. The outside diameter of the tank is 12 ft and the wall thickness is 0.375 in. Determine the maximum normal stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft3.)
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
A cylindrical tank with closed ends is filled with compressed air at a pressure of 500 kPa. The inner radius of the tank is 2 m and it has wall thickness of 10 mm. The magnitude of maximum in-plane shear stress (in MPa) is_______.
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm
The tank shown in the figure is fabricated from 10 mm steel plate. determine the maximum longitudinal and circumferential stress caused by an internal pressure of 1.2 mpa
An 8 mm thick steel plate has an outside diameter of 600 mm and a length of 3 m. The plate is subjected to and internal pressure of 2 MPa. 54. When the tank is filled with water, determine the circumferential stress in MPa Determine the longitudinal stress in MPa at the bottom of the tank when filled with water.
The cylindrical tank with a spherical end cap has an outer radius of 2 m and a wall thickness of 50 mm. If the tank is pressurized to 3.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the end cap. (Show free body diagram and complete solution)
The propane storage tank shown in Photo has an outer diameter of 3.3 m and a wall thickness of 18 mm. At a time when the inter-nal pressure of the tank is 1.5 MPa, determine the maximum normal stress in the tank.
An upright cylindrical tank 15 m in diameter and 13 m high is completely filled with water determine the minimum thickness of the tank plating if the stress is limited to 40 Mpa.
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjecte to an external load of 15 kN as shown. Calculate the maximum circumferential and longitudinal stresse (in MPa) experienced by the tank. The thickness of the tank is 30 mm. 175 cm 60cm 115 KN