An 8 mm thick steel plate has an outside diameter of 600 mm and a length of 3 m. The plate is subjected to and internal pressure of 2 MPa. 54. When the tank is filled with water, determine the circumferential stress in MPa Determine the longitudinal stress in MPa at the bottom of the tank when filled with water.

An 8 mm thick steel plate has an outside diameter of 600 mm and a length of 3 m. The plate is subjected to and internal pressure of 2 MPa. 54. When the tank is filled with water, determine the circumferential stress in MPa Determine the longitudinal stress in MPa at the bottom of the tank when filled with water.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
An upright cylindrical tank 15 m in diameter and 13 m high is completely filled with water determine the minimum thickness of the tank plating if the stress is limited to 40 Mpa.
A 4-ft diameter spherical tank is subjected to an internal pressure of 12 psf. If the wall thickness is 0.38", determine the tangential stress of the wall in psi.
Determine the largest internal pressure that can be applied to a cylin-drical tank of 5.5-ft outer diameter and 5/8-in. wall thickness if the ulti-mate normal stress of the steel used is 65 ksi and a factor of safety of 5.0 is desired
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm
The tank shown is fabricated from steel plate. Determine the required thickness of plate which maybe used if the stress along the transverse direction is to be used which is equal to 40 MPa and the internal pressure is 1.5 MN/m2
The propane storage tank shown in Photo has an outer diameter of 3.3 m and a wall thickness of 18 mm. At a time when the inter-nal pressure of the tank is 1.5 MPa, determine the maximum normal stress in the tank.
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
The spherical gas tank is fabricated by bolting together two hemispherical thin shells. If the 8-m inner diameter tank is to be designed to withstand a gauge pressure of 2 MPa, determine the minimum wall thickness of the tank and the minimum number of 25-mm diameter bolts that must be used to seal it. The tank and the bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively.
A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE THE MINIMUM THICKNESS OF THE TANK IF THE STRESS IS LIMITED TO 70 MPa. (note: Diam = L1, Height = L2) L1 = 5 L2 = 7
An 8 mm thick cylindrical steel tank has an outside diameter of 600 mm and a length of 3 m. (a) when the tank is filled with water, determine the circumferential stress. (b) determine the longitudinal stress at the bottom of the when it is filled with water. (c) if the stress is limited to 5 mpa, what is the maximum height of water to which the tank maybe filled.