The 2010 Nobel Prize in Physics was awarded forthe discovery of graphene, a two-dimensional formof carbon in which the atoms form a two-Part Adimensional crystal-lattice sheet only one atomthick.Predict the molar specific heat ofgraphene. Give your answer as amultiple of R.Express your answer in terms of R.ΑΣφC

Since this is a 2-D lattice, an atom can only oscillate in 2 independent directions. Thus, the…

The 2010 Nobel Prize in Physics was awarded for the discovery of graphene, a two-dimensional form of carbon in which the atoms form a two- dimensional crystal-lattice sheet only one atom thick. Part A Predict the molar specific heat of graphene. Give your answer as a multiple of R. Express your answer in terms of R. ΑΣφ C O II

The 2010 Nobel Prize in Physics was awarded for the discovery of graphene, a two-dimensional form of carbon in which the atoms form a two- dimensional crystal-lattice sheet only one atom thick. Part A Predict the molar specific heat of graphene. Give your answer as a multiple of R. Express your answer in terms of R. ΑΣφ C O II

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter4: The Second Law Of Thermodynamics

Section: Chapter Questions

Problem 50P: One mole of an ideal gas doubles its volume in a reversible isothermal expansion. (a) What is the...

See similar textbooks

Similar questions

Professional divas sometimes use heliox, consisting of 79% helium and 21% oxygen by mole. Suppose a perfectly rigid scuba tank with a volume of 11 L contains heliox at an absolute pressure of 2.1107 Pa at a temperature of 31 . (a) How many moles of helium and how many moles of oxygen are in the tank? (b) The diver goes down to a point where the sea temperature is 27 while using a negligible amount of the mixture. As the gas in the tank reaches this new temperature, how much heat is removed from it?
A bullet of mass 10 g is traveling horizontally at 200 m/s when it strikes and embeds in a pendulum bob of mass 2.0 kg. (a) How much mechanical energy is dissipated in the collision? (b) Assuming that Cv for the bob plus bullet is 3R, calculate the temperature increase of the system due to the collision. Take the molecular mass of the system to be 200 g/mol.
Calculate the length of a 1-meter rod of a material with thermal expansion coefficient a when the temperature is raised from 300 K to 600 K. Taking your answer as the new initial length, find the length after the rod is cooled back down to 300 K. Is your answer 1 meter? Should it be? How can you account for the result you got?
Substance A has twice the specific heat of substance B. Equal masses of the two substances, at different temperatures, are placed in thermal contact and allowed to come to equilibrium. (a) What is the ratio QB /QA of the energy transferred to (or from) the samples? (Hint: Remember to include the correct signs.) (b) What is the ratio ΔTB /ΔTA of their temperature changes?
5 mole of an ideal gas for which Cv,m=3/2R, initially at 20 oC and 1 atm undergoes atwo-stage transformation. For each of the stages described in the following list,Calculate the final pressure as well as q, w, ∆U, ∆H and ∆S.a) The gas is expanded isothermally and reversibly until the volume doubles.b) then, the temperature is raised to T=1000/X oC at the constant volume.Note: R= 8.314 j/mol.K or 0.082 lt.atm/mol.K, 1lt.atm= 101.325 joule x=4.5
Jill takes in 0.0140 mol of air in a single breath. The air is taken in at 20.0°C and exhaled at 35.0°C. Her respiration rate is (2.00x10^1) breaths per minute. At what average rate does heat leave her body due to the temperature increase of the air? Provide your answer to three significant figures. HINT: Use the molar specific heat at constant volume to find the heat loss, where Cv = 5R/2 (for an ideal diatomic gas).
Answer the following by filling the blank: During a bout with the flu, an 80-kg person ran a fever of 39 oC. Consider that the specific heat of any human body is 3470 J/kg K, how much energy does the body need to burn to reach the fever temperature? The answer (in fundamental SI unit) is ___________ (type the numeric value only, dont use scientific notation)
Consider a hot semi-infinite solid at an initial temperature of Ti that is exposed to convection to a cooler medium at a constant temperature of T`, with a heat transfer coefficient of h. Explain how you can determine the total amount of heat transfer from the solid up to a specified time to.
B) i) In the lab there are some sample materials, as mentioned in table below. Hasan wants to identify a material in the physics lab, and he chose one material of Area 6 cm2 and 3 cm thick. He heats up that material from 290 K to 305 K. If rate of heat flow is 24 watt (J/s), then find out, through calculation, which material he has chosen. ii) In the above table, which material will conduct more energy in 120 secs?
A 0.617 mol sample of Xe(g) initially at 298 K and 1.00 atm is held at constant volume while enough heat is applied to raise the temperature of the gas by 14.9 K. Assuming ideal gas behavior, calculate the amount of heat (?)in joules required to affect this temperature change and the total change in internal energy, Δ?. Note that some books use Δ? as the symbol for internal energy instead of Δ?. Type of gas Molar heat capacity at constant volume (??,?) atoms (3/2)? linear molecules (5/2)? nonlinear molecules 3? where ? is the ideal gas constant
ANSWER THE FF and SHOW COMPLETE SOLN: a.) An aluminum sheet of thickness 8.3 cm and area 13 m^2 is welded on top of a brass sheet of the same thickness and area. The thermal conductivities of aluminum and brass are 205 W/m·K and 109 W/m·K, respectively. The aluminum end is kept at 20 °C while the brass end is kept at 30 °C. At the moment when the interface temperature is 24 °C, what is the heat current through the brass sheet? (answer for this is: 102 kW) b.) A 10.0-cm long steel rod is welded end to end to a 20.0-cm long copper rod of the same cross-sectionalarea. The thermal conductivities of steel and copper are 50.2 W/m·K and 385 W/m·K, respectively. The steel endis kept at 100 °C while the copper end is kept at 0 °C. What is the steady-state temperature at the interfaceconnecting the two rods? (answer for this is 20.7 °C)
a. 1 kg of water at 70 oC is poured into a 1 kg copper cup initially at 20 oC. The specific heat of copper is ccopper= 390 J/kgoC⋅ and that of water cwater= 4,186 J/kgoC. What will be the equilibrium temperature of the system? b. From the answer found above, determine how many Joules of heat the cut will receive during this process