The 27-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.2 m. Determine its mass moment of inertia /o (in kg⋅m²) about point O. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer

The 27-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.2 m. Determine its mass moment of inertia /o (in kg⋅m²) about point O. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.95P

See similar textbooks

Similar questions

A truck with four wheels, each 750 mm diameter, travels on rails round a curve of 75 m at a speed of 50 km/h. The total mass of the truck is 5 t and its centre of gravity is midway between the axles, 1.05 m above the rails and midway between them. Each pair of wheels is driven by a motor rotating in the opposite direction to the wheels and at four times the speed. The moment of inertia of each pair of wheels is 15 Kgm2. The rails lie on a horizontal plane and 1.45 m apart. Determine the load on each rail.
By joining two equal cones, the similar shaped object has a side length u cm and = 90⁰. The mass of this object with respect to the ysymmetry axis is kgm2 until its moment of inertia? (Ρ = 2700kg / m3) the volume of a cone is (1/3) πR2h and its mass moment of inertia = (3/10) mR2 with respect to its axis of metrics. u = 46
(a) Show that the polar radius of gyration rO of the annular area shown is approximately equal to the mean radius Rm = (R1 + R2)/2 for small values of the thickness t = R2 – R1. (b) Determine the percentage error introduced by using Rm in place of rO for the following values of t/Rm: 1, 1/2, and 1/10.
A) Determine the position of the center of gravity of the figure's structure. B)Determine the moment of inertia of mass with respect to the x' axis that passes through the structure's center of gravity and is parallel to the x axis. The cone has a density of 600 kg/m3 and the cylinder a density of 800 kg/m3. Consider H = 83
Determine the rotational inertia of the device shown below. R = 0.50 m, r = 0.2 m, the mass of the box is 30 kg. When Fapp= 176 N, the box has an upward acceleration of 0.8 m/s2. Use g = 9.8 N/kg.
The uniform lamina of density 2.2 kg/m2. for a=2.2 m,b=4.8 m,c=8 m,d=8.9 m 1-The x-co-ordinate of total area centroid is: (a.8.27 - b.13.17 - c.7.05 - d.8.88 - e.6.13) 2- The y-co-ordinate of total area centroid is: (a.1.96 - b.2.68 - c.3.04 - d.1.61 - e.3.57) 3- The total mass is : ( a. 163.00 - b. 326.00 - c. 244.50 - d. 81.50 - e. 40.75 )
it is known that the shaft in the shape with a rotating disk on it rotates parallel to the horizontal plane. rotation speeds are wr=955 wp=296 rpm. Find the mass of the rotating disk to remain in a parallel position.gravitational acceleration g=9.81 m 2. mass moment of inertia of disk I=0.090479 kgm 2
The total mass of the Baja car and driver, including the wheels, is 250 kg. Each pair of 58-cm radius wheels and the axle has a total mass of 20 kg and a mass moment of inertia of 2.9 kg·m2 . The center of gravity of the driver and Baja body (not including the wheels) is located x = 0.70 m from the rear axle A and y = 0.55 m from the ground. The wheelbase is L = 1.60 m. If the engine exerts a torque of 500 N·m on the rear axle, what is the car’s acceleration?
When using T = ½ I + ½ m vG 2 for kinetic energy of a planer rigid body, what point must the mass moment of inertia I be found about?
The moment of inertia of a rectangular plate of width ‘b’ and height ‘d’ about Y - Y axis passing through its center of gravity is Select one: bh3/12 bd3/12 db3/12 dh3/36
If a walking stick with a mass of 300 g can be balanced by placing a mass M of 120 g at a distance L of 30 cm from the fulcrum. Determine the position of the centre of gravity of the stick with respect to the fulcrum
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and ka = 4.000 N-m/rad. The turbine generates a harmonic torque given by M(t) = M, cos at about the shaft axis with M, = 200 N-m and e = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, )