Determine the state of stress at point A of the rectangular post shownloaded with concentrated forces directed along the y axis equal to 75kNand along the x axis equal to 15kN.75 KNa) Determine the equivalent internalforces and moments at the sectioncontaining points A50 mmF₂=Fy=F₂=M₂=M,=M,=b) Determine the total normal stressalong the x and y axes at point A(include if tensile or compressive inyour final solutions)σμ²ƠAy²c) Determine the total shear stressat point ATA=d) Draw the state of stress of pointA15 KN200 mmA150 mm50 mm800 mm

Given: Force in downward y direction=75 KN And force in negative x direction=15 KN Distance of the…

Determine the state of stress at point A of the rectangular post shown loaded with concentrated forces directed along the y axis equal to 75kN and along the x axis equal to 15kN. 75 kN 50 mm a) Determine the equivalent internal forces and moments at the section containing points A F₁= Fy= F₂= M₂= M,= M,= b) Determine the total normal stress along the x and y axes at point A (include if tensile or compressive in your final solutions) σμ= OAy c) Determine the total shear stress at point A TA= d) Draw the state of stress of point A 15 KN 200 mm 150 mm 50 mm 800 mm

Determine the state of stress at point A of the rectangular post shown loaded with concentrated forces directed along the y axis equal to 75kN and along the x axis equal to 15kN. 75 kN 50 mm a) Determine the equivalent internal forces and moments at the section containing points A F₁= Fy= F₂= M₂= M,= M,= b) Determine the total normal stress along the x and y axes at point A (include if tensile or compressive in your final solutions) σμ= OAy c) Determine the total shear stress at point A TA= d) Draw the state of stress of point A 15 KN 200 mm 150 mm 50 mm 800 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine: a) State of stress at point A on the upper surface of the shaft b) The maximum normal stresses at point A as we well as its orientation c) Of the 800lb force is going upwards (instead of downwards) explain what will happen to i) normal stress, and ii) shear stress at A (no calculations needed for part c)
Using transformation equations of plane stress, determine the normal and shear stress components for X’-axis located 0.5 radians clockwise from x-axis. The non-zero stress components are given as follows, σx= 200 MPa, σy= 100 MPa, τxy= -50 MPa.
The beveled gear is subjected to the loads shown.Determine the stress components acting on the shaftat point B, and draw the results on a stress elementat this point. The shaft has a diameter of 1 in. and isfixed to the wall at C. A = 0.7854 in2 J = 0.098175 in4 I = 0.049087 in4 (QB)z = 0 (QB)x = 0.0833 in3
Determine the average normal stress developed at points A, B, and C. The diameter ofeach segment is indicated in the Figure below.
a. Determine the principal stresses at point A on the cross section of the wrench at section a-a. Also Specify the orientation for this state of stress. b. Determine maximum in-plane shear stress at point A on the cross section of the wrench at section a-a. Also Specify the orientation for this state of stress.
Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure.
!! Show Complete & Detailed Solution w/ FBD !!From the figure shown, the diameter of each segment is indicated. Determine the average normal stress developed at points.a. Ab. Bc. C.
Determine the equivalent state of stress if an element is oriented 60° clockwise from the element shown.
Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated in the figure.
The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a differential volume element located at this point.
Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case.
Determine the state of stresses at point A.