The 510-kg engine is suspended from the jib crane at the position shown. (Figure 1) Figure Ac 2m- 0.4 m 150 mm TSPT 150 mm 20 mm 20 mm- MA 300 mm B < 1 of 1 20 mm Section a-a Part A Determine the normal stress at point A on the cross section of the boom at section a a Express your answer using three significant figures and include the appropriate unit σA= Part B Submit Previous Answers Request Answer μA -3.327 ΤΑ X Incorrect; Try Again; 5 attempts remaining Submit Determine the shear stress at point A Express your answer to three significant figures and include the appropriate units. Provide Feedback MPa μA Value Request Answer ? Units ?

The 510-kg engine is suspended from the jib crane at the position shown. (Figure 1) Figure Ac 2m- 0.4 m 150 mm TSPT 150 mm 20 mm 20 mm- MA 300 mm B < 1 of 1 20 mm Section a-a Part A Determine the normal stress at point A on the cross section of the boom at section a a Express your answer using three significant figures and include the appropriate unit σA= Part B Submit Previous Answers Request Answer μA -3.327 ΤΑ X Incorrect; Try Again; 5 attempts remaining Submit Determine the shear stress at point A Express your answer to three significant figures and include the appropriate units. Provide Feedback MPa μA Value Request Answer ? Units ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.14P: Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82...

See similar textbooks

Similar questions

Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa isa) 150 MPA b ) 125 MPa c) 175 MPa d ) 200 MPa e) none of these
circular cross-section belt pulley system supported by two bearings tensioning forces formed in belts in Shaft power transmission T11 = 8 kN, T12 = 2 kN, T21 = 8 kN and T22 = 2 kN. Pulley weights are 1 no.lu pulley for both pulleys W =6 kN. Each two pulley diameters d = 1,2 m dir. a = 0.2 m ve b = c = 0,4 m. Slip safety stress Jul = 70 MPa a-) Greatest shear stress (TRESCA) b-) The diameter of the shaft (d) according to the largest change in shape (VON MISES) criteriayou can find.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
Question twoa) Shafts and tubes having circular cross sections cannot be used to transmit powerdeveloped by a machine. True or False? b) Explain the concept of torsion. c) If the applied torque on shaft CD is T = 75 N.m, determine the absolute maximumshear stress in each shaft. The bearings B, C, and D allow free rotation of the shafts,and the motor holds the shafts fixed from rotating
The shaft assembly is made from a steel tube 1 in. in diameter,which is bonded to a solid brass core 0.5 in. in diameter. If atorque of 250 lb-ft is applied at its end, determine the maximumshear stress in psi experienced by the assembly. Take G for steelat 11.4x103 ksi and G brass at 5.2 x 103 ksi.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating at 40 rad>s, it transmits 25 kW of power from the motor M to the pump P. Determine the smallest thickness of the tube if the allowable shear stress is tallow = 80 MPa.
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
A cylindrical tank has an inner radius of 750mm and length of 3.0m. Determine its minimum thickness (to nearest mm) if it is subjected to an internal pressure of 150kPa and tangential stress is not to exceed by 12MPa. Indicate the free body diagram
A simple truss is subjected to a vertical load F = 500 lb.Determine the minimum diameter of the pin at C if theallowable shear stress on the pin is 20 psi.Answers: d =___________________