The 53-kg cylinder is suspended from a clamping collar at C which can be positioned at any horizontal position x between the fixed supports at A and B. The cable is 8 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x over the interval 0 ≤ x ≤ 7. Do your plot on a separate piece of paper. Then answer the questions to check your results. A Questions: 7 m C 53 kg (a) If x= 2.6 m, the tension in cable AC is B i (b) If x= 4.9 m, the tension in cable BC is i 55.6 55.7 N N

The 53-kg cylinder is suspended from a clamping collar at C which can be positioned at any horizontal position x between the fixed supports at A and B. The cable is 8 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x over the interval 0 ≤ x ≤ 7. Do your plot on a separate piece of paper. Then answer the questions to check your results. A Questions: 7 m C 53 kg (a) If x= 2.6 m, the tension in cable AC is B i (b) If x= 4.9 m, the tension in cable BC is i 55.6 55.7 N N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 55-kg cylinder is suspended from a clamping collar at C which can be positioned at any horizontal position x between the fixed supports at A and B. The cable is 9 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x over the interval 0≤x≤7. Do your plot on a separate piece of paper. Then answer the questions to check your results. (You can disregard the plot, I only need the answer for the given x value)
The 55-kg cylinder is suspended from a clamping collar at C which can be positioned at any horizontal position x between the fixed supports at A and B. The cable is 14 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x over the interval 0≤x≤13. Do your plot on a separate piece of paper. Then answer the questions to check your results.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
2-D PROBLEM: A spherical tank with a radius of 3.41m that has a mass of 28928.644kg was supported in the system shown. Assuming friction and the bar weight is negligible, determine the following: β: 21.774° θ: 46.452° 1. The reaction @ point D. 2. Tension @cable BE 3. The x and y-component of the reaction @ A 4. The reaction @ A
ابحثوا بالملفات Q1 :Determine the tensions T₁ and T₂ in the ropes AB and CD as shown in the below Figure that were used to support a machine component has long 3 m and weight 2500 N, then discuss your results.
Determine the magnitude and direction of the angle theta of the force FAB that must be exerted on bar AB to maintain equilibrium of the system. The suspended mass is 110 kg. Neglect the size of the pulley at A and treat all pulleys as smooth. What should happen to maintain the equilibrium of the system if FAB acts with an angle theta= 0°?Consider g = 9.81 m/s2.
A 50-m steel surveying tape has a mass of 1.6 kg. If the tape is stretched between two points at the same elevation and pulled until the tension at each end is 60 N, determine the horizontal distance between the ends of the tape. Neglect the elongation of the tape due to the tension.
Two cylinders are being supported by the wires shown in the figure. Determine the following: 1.1 The tension developed in wire BC required for equilibrium of the 13.6-kg cylinder E and the 27.2-kg cylinder F is Blank 1 N. 1.2 The angle required for equilibrium of the 13.6-kg cylinder E and the 27.2-kg cylinder F is Blank 2°. 1.3 If cylinder E weighs 37 lb and = 12.8°, determine the weight of cylinder F.
1. Samer (ms = 75 kg) is sitting on the seat of a swing at the playground. The seat is supported by two cables, one on each side of the seat. (You may assume the seat has negligible mass.) A. Determine the tension in each cable due to Samer sitting on the swing seat. B. Given each cable has a diameter of 1 mm and each cable is exactly 5 m long before Samer sits on the seat, determine the length of each cable when Samer is sitting on the seat. (The cables are made of Aluminum for which Y = 70 GN/m°.) show all work in logical, detailed form and box in numerical answers. Include a diagram wherever possible. On any problem where an FBD is appropriate, it must be included for maximum credit. All numerical results should be stated to 3.00 or 4.000 significant figures and in mks units unless otherwise noted.
A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
The uniform plate has a weight of W = 450 lb. Suppose that F= 250 lb. The plate is supported by cables A, B, and C as shown below. Determine: A) The tension in the supporting cable A. B) The tension in the supporting cable B. C) The tension in the supporting cable C.
The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at point B. Determine the following: a.) The Tension at Point B. b.) The Reaction at Point A.