Give me correct answer otherwise skip it please II ReviewThe 56-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when thetemperature is T, = 20°C.(Figure 1)Part AIf the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snugwith negligible force against the rigid jaws, determine the force°C.the cylinder when the temperature rises to T, = 130Express your answer to three significant figures and include the appropriate units.?Figure1 of 1F= 1.10 • 103NSubmitPrevious Answers Request AnswerX Incorrect; Try Again; 5 attempts remaining100 mm150 mmProvide FeedbackNext >

Answered: The 56-mm-diameter cylinder is made…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 0.35-inch-diameter cylinder is made from C83400 red brass and is placed in the device depicted below when temperature is T1 = 5 oF throughout. The two Am 1004-T-61 magnesium alloy carriage bolts each have a diameter of 0.10 inches and hold the cylinder snug with negligible force against the rigid jaws. Determine the maximum temperature (in oF) that the brass cylinder can be subjected to without causing yielding of any one of the materials. The end plates will not deform or fail.
The brass tube AB (E = 105 GPa) has a cross-sectional areaof 138 mm² and is fitted with a plug at A. The tube is attached atB to a rigid plate that is itself attached at C to the bottom of analuminum cylinder (E = 70 GPa) with a cross-sectional areaof 250 mm². The cylinder is then hung from a support at D. In orderto close the cylinder, the plug must move down through 1.2 mm. Determine the force P that must be applied to the cylinder.
The assembly is made of A-36 steel cylinders. (Figure 1) Part A: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 220 kN is applied. Enter your answers in kilonewtons to three significant figures separated by a comma. Fa, Fd = ?
Three steel rods (E = 200 GPa) supports a 50 kNload P. Each of the rods AB and CD has a 300 mm2cross-sectional area and rod EF has a 600 mm2cross-sectional area.(a) State whether the structure isstatically determinate or indeterminate.Why?(b)Determine the force and thestress in each rod.(c) Determine the deformation of each rod.Note: The link BED is rigid, and BE = ED.
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
The vertebra of the spinal column can support a maximum compressive stress of smax, before undergoing a compression fracture. Determine the smallest force P that can be applied to a vertebra, if we assume this load is applied at an eccentric distance e from the centerline of the bone, and the bone remains elastic. Model the vertebra as a hollow cylinder with an inner radius ri and outer radius ro.
Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 18 ksi and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD. Take P = 148 kips.The smallest-diameter rod that can be used for member BD is in.
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) Sketch the free body diagram and calculate the internal forces acting in each section of the rod. (b) Determine the average normal stress developed in rods FG, EF and AB. (c) Determine the average normal strain in the rod of AB.(d) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.
A six-pack is shaken so that the pressurein each can is p = 20 psi. A board is placed onthe six pack and a student(s) weighing Wstands on the board so his weight is evenlydistributed to the six cans. The aluminumproperties are E = 10,000 ksi, Sy = 35 ksi, andν = 0.33. Each can has an average radius ofR = 1.25 in., thickness t = 0.01 in., and lengthL = 4.50 in.(a) Determine the critical weight of thestudent, Wcr , so that a stress element on thesurface of the can is in a state of uniaxial stress.Assume that no support is provided by thecontained liquid and the cans do not fail bybuckling (being crushed). (b) Determine thestrain in the longitudinal direction of the candue to pressure p = 20 psi and force Wcr.(c) Determine the strain in the hoop directionof the can due to pressure p = 20 psi and forceWcr
The assembly shown consists of twoA36 steel bolts AB and EF and an 6061-T6aluminum rod CD. When the temperature is at30°C, the gap between the rod and rigid memberAE is 0.1 mm. Determine the highest temperatureto which the assembly can be raised withoutcausing yielding either in the rod or the bolts.Assume BF is also rigid.
The load is supported by the four stainless steels wires that are connected to the rigid members AB and DC. The members were originally horizontal, and each wire has a cross-sectional area of 16mm2. Given that E= 200Gpa for all the steel wires. a) Draw Freee Body Diagram(FBD) of each rigid member. b) Determine the angle of tilt of each member after the 2250N load is applied

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS