3 4The AC EMF in this electric circuit is described by the following equation:e = (15V) e (23 4)*If C1 = 19mF, R1 = 2N, L1 = 7mH, and R2 = 5N, what is the average power (in W) supplied by the EMF to the electric circuit?wwR2L1wwR1

Answered: Image /qna-images/answer/47784353-496c-44c0-8e60-f6f22c08ee28.jpg

The AC EMF in this electric circuit is described by the following equation: e = (15V) e(23 )* If C1 = 19m F,R1 = 2N, L1 = 7mH, and R2 = 5N, what is the average power (in W) supplied by the EMF to the electric circuit?

The AC EMF in this electric circuit is described by the following equation: e = (15V) e(23 )* If C1 = 19m F,R1 = 2N, L1 = 7mH, and R2 = 5N, what is the average power (in W) supplied by the EMF to the electric circuit?

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter20: Electric Current, Resistance, And Ohm's Law

Section: Chapter Questions

Problem 91PE: (a) What is the resistance of a 220-V AC short circuit that generates a peak power of 96.8 kW? (b)...

See similar textbooks

Similar questions

A certain lightbulb is rated at 60.0 W when operating at an rms voltage of 120 V. (a) What is the peak voltage applied across the bulb? (b) What is the resistance of the bulb? (c) Does a 100-W bulb have greater or less resistance than a 60.0-W bulb? Explain.
(a) What is the resistance of a 220-V AC short circuit that generates a peak power of 96.8 kW? (b) What would the average power be if the average power be if the voltage was 120 V AC?
Neon signs require 12-kV for their operation. A transformer is to be used to change the voltage from 220-V (rms) ac to 12-kV (rms) ac. What must the ratio be of turns in the secondary winding to the turns in the primary winding? (b) What is the maximum rms current the neon lamps can draw if the fuse in the primary winding goes off at 0.5 A? (C) How much power is used by the neon sign when it is drawing the maximum current allowed by the fuse in the primary winding?
(a) What is the resistance of a 220-V ac short circuit that generates a peak power of 96.8 kW? (b) What would the average power be if the voltage were 120 V ac?
The capacitor in Figure 23.55(a) is designed to filter low—frequency signals, impeding their transmission between circuits. (a) What capacitance is needed to produce a 100 k reactance at a frequency of 120 Hz? (b) What would its reactance be at 1.00 MHz? (c) Discuss the implications of your answers to (a) and (b).
(a) The plug-in transformer for a laptop computer puts out 7.50 V and can supply a maximum current of 2.00 A. What is the maximum input current if the input voltage is 240 V? Assume 100% ef?ciency. (b) If the actual efficiency is less man 100%, would the input current need to be greater or smaller? Explain.
Some surgery is performed with high-voltage electricity passing from a metal scalpel through the tissue being cut. Considering the nature of electric fields at the surface of conductors, why would you expect most of the current to flow from the sharp edge of the scalpel? Do you think high- or low-frequency AC is used?
A series RLC circuit is operating at 2.00 103 Hz. At this frequency. XL = XC = 1 884 . The resistance of the circuit is 40.0 . (a) Prepare a table showing the values of XL, XC, and Z for f = 300, 600, 800, 1.00 103, 1.50 103, 2.00 103, 3.00 103, 4.00 103, 6.00 103, and 1.00 104 Hz. (b) Plot on the same set of axes XL, XC, and Z as a function of ln f.
(a) What current flows when a 60.0 Hz, 480 V AC source is connected to a 0.250 (F capacitor? (b) What would the current be at 25.0 kHz?
For the circuit shown in Figure P18.30, use Kirchhoffs rules to obtain equations for (a) the upper loop, (b) the lower loop, and (c) the node on the left side. In Figure P18.29 each case suppresses units for clarity and simplify, combining like terms. (d) Solve the node equation for I36. (e) Using the equation found in (d), eliminate I36 from the equation found in part (b). (f) Solve the equations found in part (a) and part (e) simultaneously for the two unknowns for I18 and I12, respectively. (g) Substitute the answers found in part (f) into the node equation found in part (d), solving for I36. (h) What is the significance of the negative answer for I12? Figure P18.30
For the circuit shown in Figure P18.30, use Kirchhoffs rules to obtain equations for (a) the upper loop, (b) the lower loop, and (c) the node on the left side. In Figure P18.29 each case suppresses units for clarity and simplify, combining like terms. (d) Solve the node equation for I36. (e) Using the equation found in (d), eliminate I36 from the equation found in part (b). (f) Solve the equations found in part (a) and part (e) simultaneously for the two unknowns for I18 and I12, respectively. (g) Substitute the answers found in part (f) into the node equation found in part (d), solving for I36. (h) What is the significance of the negative answer for I12? Figure P18.30
An AC power supply produces a maximum voltage Vmax = 100 V. This power supply is connected to a resistor H = 24.0 , and the current and resistor voltage are measured with an ideal AC ammeter and voltmeter as shown in Figure P33.3. An ideal ammeter has zero resistance, and an ideal voltmeter has infinite resistance. What is the reading on (a) the ammeter and (b) the voltmeter?