The angular displacement of the centrifuge is given by 0 = 4.1[t+ 37e-0.018t - 37] rad, where t is in seconds and t = 0 is the startup time. If the person loses consciousness at an acceleration level of 8.5g, determine the time t at which this would occur. Verify that the tangential acceleration is negligible as the normal acceleration approaches 8.5g.

The angular displacement of the centrifuge is given by 0 = 4.1[t+ 37e-0.018t - 37] rad, where t is in seconds and t = 0 is the startup time. If the person loses consciousness at an acceleration level of 8.5g, determine the time t at which this would occur. Verify that the tangential acceleration is negligible as the normal acceleration approaches 8.5g.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the angular velocity, in rpm, of the rotating drum which results in loss of contact between the clothes and the drum at 1.0239 rad. Assume that the small vanes prevent slipping until loss of contact. Round your answer to 2 decimal places
The velocity of aparticle which moves along the x-axis is given by x = 40-3t² (m/s) where t is in seconds. Calculate the displacement Ax of the particle during the interval from t=2sec to = 4 sec.
if the relation is : x=-153 + 10t + 4 1- the displacement between t1=2 ,t2=3 2- the magnitude of average velocity between t1=2,t4=4 3- the magnitude of average acceleration between t1=1,t4=5 4- the instantaneous velocity at t=2 5- the instantaneous acceleration at t=2
Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is the angular velocity of each pulley if the belt has a constant speed of 5 m/s? What is the frequency and the period of each pulley? (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R 1 = 0.3 mR 2 = 0.2 mR 3 = 0.1 m
The 100 meter diameter wheel needs to be designed so that it rotates at a constant rate and every complete revolution takes 15 minutes. The wheel has been installed in a vertical plane and the lowest seat is 2m above the ground surface. Each ride consists of only one full rotation. Find a further general expression for the horizontal displacement of the rider from its initial position with respect to both time and angle of rotation and hence determine the speed of the rider when t= 180 sec. Using calculus, determine what the maximum horizontal and vertical speeds of the rider would be and at which points during the ride they occur. State expressions for the acceleration of the rider in both horizontal and vertical directions and show that the resultant acceleration experienced by the rider is independent of where on the ride he/she might be. In designing a new wheel with the same diameter and same ride duration as before it is proposed that the wheel’s angular speed should not…
The displacement of aparticle which moves along the s axis is given by s=(-2+3t)e-0.5t,where s is in meters and t is in seconds.Plot the displacement,velocity and acceleration versus time for the first 20 seconds of motion. Detrmine the time at which acceleration is zero.
The velocity of a particle changes from -8 fps to 58 fps during a 10-sec intervalduring which its acceleration increases uniformly with the time from an initial valueof 3 fps2. Determine the displacement covered in the 10-sec interval. Draw the v-tand s-t curves.
The disk is originally rotating at ω0ω0omega_0 = 13 rad/srad/s . It is subjected to a constant angular acceleration of ααalpha = 25 rad/s Determine the magnitude of the velocity of point AA at the instant tt = 2 ss. Express your answer to three significant figures and include the appropriate units. Determine the magnitudes of the nn and tt components of acceleration of point AA at the instant tt = 2 ss. Express your answers using three significant figures separated by a comma.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.
To understand rigid-body rotation about a translating axis. An exhausted bicyclist pedals somewhat erratically. The angular velocity of the front tire, as measured with respect to an axis fixed at the tire’s center, is given by ω(t)=12t−14sin(2t) for t≥0 where t represents the time in seconds and ω(t) is measured in radians per second. Assume that the tires roll without slipping The bicycle’s front tire has a spot of paint on it. Take the spot’s position at time t=0.00s to be at angle θ=0.00 radians with respect to an axis parallel to the ground (and perpendicular to the axis fixed at the tire’s center) and take angles in the direction of the tire's rotation to be positive. What angular displacement θ(2) has the spot undergone between 0.00 and 2.0 s? If the tire’s radius is 23 cm, what is d, the magnitude of the spot’s displacement after 2.0 seconds? Which one of the following statements describes the spot’s motion at t=2.0s? The wheel’s angular acceleration is constant and the…
To determine the magnitude of the velocity and acceleration of the follower rod AB at this instant. The surface of the cam has a shape of a limacon defined by r = (200 + 100 cosθ) mm. Express your answer to three significant figures and include the appropriate units. only HANDWRITTEN answer needed ( NOT TYPED)
Two inclined shafts are connected by means of a universal joint. The speed of the driving shaftis 1000 £p.m. If the total fluctuation of speed of the driven shaft is not to exceed 12.5% of this, what is the maximum possible inclination between the two shafts? With this angle, what will be the maximum acceleration to which the driven shaft is subjected and when this will occur ? [Ans. 20.4° ; 1570 rad/s? ; 41.28°]