The answer is 10.11 m3/s Tut 1-Q4• Estimate the constant rate ofwithdrawal from a 1375 ha reservoirin a month of 30 days during whichthe reservoir level dropped by 0.75m in spite of an average inflow intothe reservoir of 0.5 Mm/day. Duringthe month, the average seepage lossfrom the reservoir was 2.5 cm, totalprecipitation on the reservoir was18.5 cm and the total evaporationwas 9.5 cm. (Problem 1.3,Subramanya 4th Ed)

Given Area = 1375 ha = 1375 X 104 m2 Time = 30 days Level drop = - 0.75 m Flow rate = 0.5 Mm3/ day =…

Answered: The answer is 10.11 m3/s

Engineering

Mechanical Engineering

The answer is 10.11 m3/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to the flow. If the differential height between the water columns connected to the two outlets of the probe is 3.2 cm, determine (a) the flow velocity and (b) the pressure rise at the tip of the probe. The air temperature and pressure in the duct are 45° C and 98 kPa, respectively
The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to flow. If the differential height between the water columns connected to the two outlets of the probe is 2.4 cm, determine the flow velocity at the center of the duct in m/s. R of air is 287 J/Kg-K.
A boy has a tank with a rectangular bottom base 40 cm by 50 cm and a height of 100 cm. The tank is initially empty and is equipped with an orifice 3 mm square (Cv=0.96 and Cc=0.62) located at the bottom of the tank. The boy first closed the orifice and start pouring water into the tank at a constant rate of 0.05 li/s. After 30 minutes, without the boy noticing it, the orifice was accidentally opened and it took another 30 minutes when the boy noticed that the orifice was already opened. What is the depth of water in the tank at that moment?
Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical reservoir and a 1-cm-diameter, 40-cm-high pipe. The funnel is always maintained full by the addition of oil from a tank. Assuming the entrance effects to be negligible, determine the flow rate of oil through the funnel and calculate the “funnel effectiveness,” which is defined as the ratio of the actual flow rate through the funnel to the maximum flow rate for the “frictionless” case.
It is observed that water at 20°C rises up to 20 m height in a tree due to capillary effect. The surface tension of water at 20°C is ?s = 0.073 N/m and the contact angle is 20°. The maximum diameter of the tube in which water rises is (a) 0.035 mm (b) 0.016 mm (c) 0.02 mm (d) 0.002 mm (e) 0.0014 mm
Freshwater and seawater flowing in parallel horizontalpipelines are connected to each other by a double Utubemanometer, as shown in Fig. P2–59. Determine the pressuredifference between the two pipelines. Take the density of seawaterat that location to be r = 1035 kg/m3. Can the air columnbe ignored in the analysis?
Air flows steadily and isentroplcally into an aircraft inlet at a rnass flow rateof 100 kgs·1• At a section where the cross-sectional area is 0.5 m2 , thetemperature and pressure are 200 K and 20 kPa, respectively. Determinethe velocity, pressure and cross-sectional area at a downstream sectionwhere the temperature is 350 K. Sketch the flow passage, and show the ·process on a T-s diagram
The compressed air requirements of a manufacturing facility are met by a 120-hp compressor that draws in air from the outside through an 9-m-long, 22-cm-diameter duct made of thin galvanized iron sheets. The compressor takes in air at a rate of 0.27 m3/s at the outdoor conditions of 15°C and 95 kPa. Disregarding any minor losses, determine the useful power used by the compressor to overcome the frictional losses in this duct.
The 64-W fan in an aircraft environmental system is to circulate air through the ducting. An analysis of the flow shows that the fan needs to raise the pressure of air by 47 Pa to maintain flow. The fan is located in a horizontal duct with a circular cross-section whose diameter = 30 cm at both the inlet and the outlet. Determine the highest possible average flow velocity in the duct. Give your answer in m/s. Assume the fan operates steadily and that the changes in kinetic and potential energies across the fan are negligible. Note: I start this one by finding the volumetric flow rate from the work input and the pressure rise. Then I divide that by the cross-sectional area of the duct to get velocity.
A garden hose attached with a nozzle is used to fill a 10-gal bucket. The inner diameter of the hose is 2.0cm, and it reduces to 0.8 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with water, determine the mass flow rates of water through the hose.
Consider a conical water tank with a base and height of 8m and 10m, respectively. How much work will it require to pump its content to the top if initially it is half-full?
The water at 20°C in a 10-m-diameter, 2-m-high aboveground swimming pool is to be emptied by unplugging a 5-cm-diameter, 25-m-long horizontal plastic pipe attached to the bottom of the pool. Determine the initial rate of discharge of water through the pipe and the time (hours) it would take to empty the swimming pool completely assuming the entrance to the pipe is well-rounded with negligible loss. Take the friction factor of the pipe to be 0.022. Using the initial discharge velocity, check if this is a reasonable value for the friction factor.