The area of a square gate is (12.69m) provided in oil tank is hinged at its top edge figure below. Determine the necessary vertical pull to be applied at the lower edge to open the gate (N). Gasoline surface Negative pressure (8250N/m2) 1.8m Gaseline (S-0.77 hinge gate Vertical pull F

The area of a square gate is (12.69m) provided in oil tank is hinged at its top edge figure below. Determine the necessary vertical pull to be applied at the lower edge to open the gate (N). Gasoline surface Negative pressure (8250N/m2) 1.8m Gaseline (S-0.77 hinge gate Vertical pull F

Name: The area of a square gate is (12.69m) provided in oil tank is hinged
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The area of a square gate is (12.69m) provided in oil tank is hinged atits top edge figure below. Determine the necessary vertical pull to beapplied at the lower edge to open the gate (N).Gasoline surfaceNegative pressure (8250N/m?)1.8mGaseline (S-0

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

An inclined rectangular gate AB is constructed at the bottom of a vertical surface of an open dam as shown in the figure below. The gate is 2.5 m wide and 4.0 m long. What is the pressure force of water to the gate? Express your answer in kN.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown . The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Using appropriate software, investigate the effect of water depth on the force exerted on the plate by the ridge. Let the water depth vary from 0 to 5 m in increments of 0.5 m. Tabulate and plot your results.
A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as shown inthe Figure 2 below. The plate is hinged about a horizontal axis along its upper edge through a point Aand is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate bythe ridge. Clearly state all asuumptions and illustrations.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Figure. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B.Determine the force exerted on the plate by the ridge.
The cylindrical water tank in Fig. is being fi lled ata volume fl ow Q 1 = 1.0 gal/min, while the water alsodrains from a bottom hole of diameter d = 6 mm. At timet = 0, h = 0. Find and plot the variation h ( t ) and the eventualmaximum water depth h max . Assume that Bernoulli’ssteady-fl ow equation is valid.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Fig. below. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge.
Panels AB and CD in Fig. are each 120 cm wide intothe paper. ( a ) Can you deduce, by inspection, which panelhas the larger water force? ( b ) Even if your deduction isbrilliant, calculate the panel forces anyway.
The distance between the centers of the two arms of a U-tube open to the atmosphere is 30 cm, and the U-tube contains 20 cm high alcohol in both arms. Now the U-tube is rotated about the left arm at 4.2 rad/s. Determine the elevation difference between the fluid surfaces in the tow arms. Include the free body diagram in your solution. a.0.96 m b.0.67 m c.0.33 m d.0.81 m
A cylinder tank of 3m height and 5 cm2 cross section area isfilled with water upto height 2m and remaining with oil ofspecific gravity 0.8. The vessel is open to atmospherecalculate i. pressure intensity at interface and ii) pressureintensity at base of tank
Flat plate, moves at speed u0 over a fixed plate, with the intermediate layer consisting of oil. a) If the velocity profile isparabolic (u2 = a ∙ y) find the stress on the moving plate. b) What is its value if the velocity profile is linear.Result: α) τ=-μu0/2d, β) τ=-μu0/d
A tube with diameter of 0.3cm is inserted into water (Surface tension= 0.061N/m). The water in the tube rises to a height of 0.45cm from the surface. Calculate the contact angle between the water and the tube.
A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).